Silverline 268819 Mode D'emploi page 9

Hammer drill mode selection
Hammer drill mode is to be used for drilling masonry and concrete.
Note: The Keyed Chuck (20) is not suitable for using in hammer drill mode
1. Adjust the Mode Selector (3) to the position by pressing the Mode Selector Lock (21) on
the Mode Selector (3) inward, and rotating the Selector
2. Release the Mode Selector Lock
3. Rotate the Standard/Hammer Drill Selector (6) to the
• Do not attempt to move the Mode Selectors while the drill is Running
• Do not attempt to operate the drill with the Mode Selectors in a mid-position
Rotary drill mode selection
Rotary drill mode is to be used when drilling wood or metal.
Note: Use the Keyed Chuck (20) for standard drilling, using standard type wood and metal drill bits
(not supplied) (see 'Installing/removing SDS accessories or Keyed Chuck')
1. Adjust the Mode Selector (3) to the position by pressing the Mode Selector Lock (21) on the
Mode Selector inward and rotating the Selector
2. Release the Mode Selector Lock
3. Rotate the Standard/Hammer Drill Selector (6) to the position
• Do not attempt to move the Mode Selectors while the drill is Running
• Do not attempt to operate the drill with the Mode Selectors in a mid-position
Chisel mode selection
Chisel mode is to be used for chiselling operations only. Only use SDS Plus chisels for chiselling
operations.
Note: The Keyed Chuck (20) is not suitable for using in chisel mode
1. Adjust the Mode Selector (3) to the position by pressing the Mode Selector Lock (21) on the
Mode Selector inward and rotating the Selector
2. Release the Mode Selector Lock
3. Rotate the Standard/Hammer Drill Selector (6) to the
• Do not attempt to move the Mode Selectors while the drill is Running
• Do not attempt to operate the drill with the Mode Selectors in a mid-position
Switching ON & OFF
1. To activate the drill, squeeze the ON/OFF Trigger Switch (5)
2. To stop the drill, release the ON/OFF Trigger Switch
Note: The maximum speed of the drill is governed by the Variable Speed Control (7). Take time
adjusting the Variable Speed Control Switch to ensure the maximum speed is correctly set before
use
Drilling concrete
1. Set the drill to hammer drill mode (see 'Hammer drill mode selection')
2. Install a Masonry SDS Plus Drill Bit (16,17,18) to the SDS Plus Chuck (1) (see 'Installing/
removing SDS accessories or Keyed Chuck')
3. Switch the drill 'ON' (see 'Switching ON & OFF')
4. Contact the drill bit with the workpiece and apply light to moderate pressure to the rear of the
drill in line with the drill bit.
5. Remove the drill from the workpiece before switching the drill 'OFF'
IMPORTANT: Do not apply excessive pressure while drilling as this will damage the motor and
drill bit.
Note: The drilled hole may fill with debris while drilling. To clear the debris, slow the speed of the
drill and remove the bit from the hole before continuing
Drilling wood and metal
1. Set the drill to rotary drill mode (see 'Rotary drill mode selection')
2. Install the Keyed Chuck (20) to the drill (see 'Installing/removing SDS accessories or Keyed
Chuck')
3. Install a standard type wood or metal drill bit (not supplied) to the Keyed Chuck (see 'Adjusting
the Keyed Chuck')
4. Switch the drill 'ON' (see 'Switching ON & OFF')
5. Contact the drill bit with the workpiece and apply light to moderate pressure to the rear of the
drill in line with the drill bit.
6. Remove the drill from the workpiece before switching the drill 'OFF'
IMPORTANT: Ensure that the drill bit being used is suitable for the workpiece
Note: The drilled hole may fill with debris while drilling. To clear the debris, slow the speed of the
drill and remove the bit from the hole before continuing
position
position
1500W SDS Plus Drill
Accessories
• A full range of accessories including SDS Plus drill and chisel bits is available from your Silverline
stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
Gearbox maintenance
See Fig. VI
After every 6 hours of use (approx.), the gearbox must be re-greased
1. Use the Hex Key (19) to remove the Gearbox Cover (4)
2. Use a spatula or similar instrument to apply grease into the gearbox
cavity until it is full (max 80g)
Note: Take care not to scratch or otherwise damage the gearbox internal mechanism
3. Replace the Gearbox Cover (4)
• A Pot of Grease (12) is supplied. When purchasing additional grease select a general purpose
lithium based grease
• Do not over-tighten the gearbox cover or overfill the gearbox with grease
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised Silverline service centre. This advice also applies to extension cords
used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly and
shorten the machine's service life. Clean the body of your tool with a soft brush, or dry cloth. If
available, use clean, dry, compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol or
strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant with the
exception of the gearbox, which requires lithium based grease
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes, remove the Brush Access Cover (8). The worn brushes can then be
withdrawn, and replaced with new.
• Always replace worn brushes in pairs.
• Refit the brush access cover.
• Alternatively, have the tool serviced at an authorised Silverline service centre
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Toolstream Ltd
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose of power
tools
silverlinetools.com
9