Troubleshooting; Radio Reception - Sony MEX-N5100BT Mode D'emploi

documentation and/or other materials provided
with the distribution.
 Neither the name of the Xiph.org Foundation nor
the names of its contributors may be used to
endorse or promote products derived from this
software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Troubleshooting

The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
For details on using the fuse and removing the unit
from the dashboard, see "Connection/Installation"
(page 32).
If the problem is not solved, visit the support site on
the back cover.
General
No power is being supplied to the unit.
 If the unit is turned off and the display
disappears, the unit cannot be operated with the
remote commander.
 Turn on the unit.
No sound or the sound is very low.
 The position of the fader control [FADER] is not
set for a 2-speaker system.
 The volume of the unit and/or connected device
is very low.
 Increase the volume of the unit and connected
device.
No beep sound.
 An optional power amplifier is connected and
you are not using the built-in amplifier.
26
GB
The contents of the memory have been erased.
 The reset button has been pressed.
 Store again into the memory.
 The power supply lead or battery has been
disconnected or not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes a noise when the position of the ignition
is switched.
 The leads are not matched correctly with the car's
accessory power connector.
During playback or reception, the demonstration
mode starts.
 If no operation is performed for 5 minutes with
[DEMO-ON] set, the demonstration mode starts.
 Set [DEMO-OFF] (page 21).
The display disappears from/does not appear in
the display window.
 The dimmer is set to [DIM-ON] (page 21).
 The display disappears if you press and hold OFF.
 Press OFF on the unit until the display appears.
 The connectors are dirty (page 24).
The operation buttons do not function.
The disc will not eject.
 The connection is not correct.
 Check the connection of the unit.
If the situation does not improve, press RESET
(page 7).
The contents stored in memory are erased.
For your safety, do not reset the unit while you
are driving.

Radio reception

Stations cannot be received.
The sound is hampered by noises.
 The connection is not correct.
 If your car has built-in radio antenna (aerial) in
the rear/side glass, connect an REM OUT lead
(blue/white striped) or accessory power supply
lead (red) to the power supply lead of a car's
antenna (aerial) booster.
 Check the connection of the car antenna
(aerial).
 If the auto antenna (aerial) will not extend,
check the connection of the power antenna
(aerial) control lead.
Preset tuning is not possible.
 The broadcast signal is too weak.
RDS
PTY displays [- - - - - - - -].
 The current station is not an RDS station.
 RDS data has not been received.
 The station does not specify the program type.