Hama Moorea Mode D'emploi page 3

G Operating instruction
1. Controls and Displays
1. TIME SET = setting the local time and foreign time
2. + = increases the current set value
3. – = reduces the current set value
4. RC On/Off = activating/deactivating RC
5. RESET = restoring factory settings
6. LOCAL/FOREIGN slide switch
= If you select 'LOCAL', the clock displays Central European Time. If you select
'FOREIGN', the clock displays the desired time zone (European time + the set
time zone -> 'F' symbol lights up)
7. Battery compartment
8. Radio symbol
9. Summer time
10. Day
11. Month
12. Day of the week
13. Room temperature
14. OFF = radio mode is deactivated
2. Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to
speci c hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
3. Package Contents
• 1 DCF radio-controlled wall clock
• 2 AA Mignon batteries
• These operating instructions
4. Safety Notes
• The product is intended for private, non-commercial use only.
• Use the product for its intended purpose only.
• Protect the product from dirt, moisture and overheating, and only use it in a dry
environment.
• Do not use the product in the immediate vicinity of heaters or other heat sources
or in direct sunlight.
• Do not operate the product continuously, as it is not designed for this.
• Do not drop the product and do not expose it to any major shocks.
• Do not attempt to service or repair the product yourself. Leave any and all service
work to quali ed experts.
• Do not put the product near interference elds, metal frames, computers, TVs,
etc. Electronic devices and window frames can negatively affect the product's
functionality.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach of children due to the risk of
suffocation.
• Dispose of packaging material immediately according to locally applicable
regulations.
• Do not operate the product outside the power limits given in the speci cations.
• Do not open the device or continue to operate it if it becomes damaged.
• Keep this product, as all electrical products, out of the reach of children!
• Use the item only in moderate climatic conditions.
Warning – Batteries
• When inserting batteries, note the correct polarity (+ and - markings) and
insert the batteries accordingly. Failure to do so could result in the batteries
leaking or exploding.
• Only use batteries that match the speci ed type. Keep the instructions for the
correct choice of batteries included with the operating instructions of devices
safe for future reference.
• Before you insert the batteries, clean the battery contacts and the polarity
contacts.
• Do not allow children to change batteries without supervision.
• Replace all the batteries in a set at the same time.
• Do not mix old and new batteries, or batteries of different types or from
different manufacturers.
• Remove the batteries from products that are not being used for an extended
period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not burn batteries or heat them up.
• Never open, damage or swallow batteries or allow them to enter the
environment. They can contain toxic, environmentally harmful heavy metals.
• Remove spent batteries from the product and dispose of them without delay.
• Avoid storing, charging and using in extreme temperatures
and at extremely low atmospheric pressures (such as at high
altitudes).
• Ensure that batteries with damaged housings do not come into
contact with water.
• Keep batteries out of the reach of children.
5. Getting Started
5.1 Inserting the battery
• Open the battery compartment (7) and insert two AA batteries with the correct
polarity into the battery compartment.
• Close the battery compartment.
• If the display remains blank after inserting a new battery, change the batteries or
press the RESET button (5) on the back of the clock using a pointed object.
5.2 Replacing the battery
• Open the battery compartment on the back of the product.
• Remove and dispose of any used batteries. Insert the new battery (AA). Ensure
that the polarity of the battery corresponds to the symbols in the battery
compartment.
• Close the battery compartment.
6. Installation
Warning – Mounting Note:
• Before mounting the clock, ensure that the chosen wall is suitable for the
weight to be mounted, and make sure that there are no electrical wires, water,
gas or other lines at the installation site on the wall.
• Purchase special fastening materials from specialised dealers.
• Do not mount the product above locations where persons might linger.
You can mount the wall clock on a wall using the opening on the back.
3