Rupes HLR75 Traduction Des Instructions Originales page 8

PARTS OF THE TOOL
1 - Identification plate
2 - ON/OFF – Speed regulation knob
3 - START/STOP switch lever
4 - Backing pad
STARTING UP
WARNING: To reduce the risk of injury, only the 18V Li-ION Battery Pack 9HB180LT (5) or the power supply 9HP180LT
(6) should be used with this product.
Since the batteries, other than those offered by RUPES, have not been tested with this product, use of such batteries with this tool
could cause the injury and property damage.
BATTERY PACK (PROVIDED OR OPTIONAL)
WARNING: For your personal safety, READ and UNDERSTAND the instruction manual of Battery pack 9HB180LT
before using.
WARNING: Avoid short circuiting the contacts. Avoid mechanical damage of the battery pack. Do not open or
disassemble. Advice on protection against fire and explosion. Keep away from open flames, hot surfaces and sources
of ignition.
Temperature in excess of 45°C reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine. Storage at
room temperature (approx. 20°C) at approx. 20~60% of the nominal capacity. Every six months of storage, charge the battery pack
as normal.
Intended use
The battery pack 9HB180LT (5) is used as the power source for RUPES HLR75.
Battery pack specifications:
Model Chemistry
9HB180LT Lithium Ion
WARNING: for other technical data refer to the label of Battery pack 9HB180LT.
WARNING: to reduce the risk of injury or explosion, never burn or incinerate a tool's battery pack even if it is
damaged, dead or completely discharged. When burned, toxic fumes and materials are created.
ASSEMBLE AND DISASSEMBLE BATTERY PACK
AWARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position.
In order to assemble the battery pack, push the clip and insert the battery pack in the tool till it is fixed.
In order to disassemble push the clip and extract the battery from the tool.
CHARGE THE BATTERY PACK
WARNING: For your personal safety, READ and UNDERSTAND the instruction manual of charging station
9HC180LT before using.
WARNING: Charge Rupes 18V Li-ION Battery pack 9HB180LT only in the Rupes 18V Li-ION Battery Charger
9HC180LT. Other types of batteries may cause personal injury and damage. This tool's battery pack and charger
are not compatible with NiCd or NiMH systems.
The battery pack(s) contained in the kit shall be charger before use. The provided battery is charged <30%.
In order to charge, connect the Li-Ion battery with a charging station 9HC180LT till the charging is completed.
Charge your battery tool when convenient for you and your job.
The Rupes Battery pack does not develop "memory" when charged after only a partial discharge.
It is not necessary to run down the battery tool pack before placing it on the charger.
Use the led Battery pack 9HB180LT level indication to determine when to charge the Rupes Battery pack.
POWER SUPPLY (PROVIDED OR OPTIONAL)
WARNING: For your personal safety, READ and UNDERSTAND the instruction manual of Power Supply
9HP180LT before using.
WARNING: Voltage and power frequency must match the data displayed on the identification plate of the 9HP180LT
power supply. Make sure that tool is switched off before plug is connected.
ASSEMBLE AND DISASSEMBLE POWER SUPPLY
WARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position.
In order to assemble the power supply, push the clip and insert the power supply in the tool till it is fixed.
In order to disassemble, push the clip and extract the power supply from the tool.
STARTING AND STOPPING
Starting: Rotate the speed regulation knob (2) and set up the speed; now the tool can be started by pressing the START/STOP switch
lever (3). The RPM can be adjusted by rotating the speed regulator knob (2).
Stopping: Release the lever for stop the tool; rotate the speed regulation knob until position 0 and the tool will have turned off.
8
5 - Battery Pack 9HB180LT
6 - Power supply 9HP180LT
7 - Backing pad screw
8 - Allen wrench
Voltage Capacity
18V 2.5 Ah
Energy Weight
45 Wh 0.360±0.005 kg