Vimar ELVOX GIOTTO 6329 Manuel Installateur page 8

PROGRAMMING
There are three monitor programming modes: assignment of an identifica-
tion code or call code (indispensable), assignment of a secondary identifi-
cation code (for monitors associated with a master monitor), programming
of pushbuttons for auxiliary services and intercommunicating calls (when
necessary).
Programming must be performed with the system switched on, without ac-
tive communication and only after connecting the interphones/monitors to
the system and programming the panels.
N.B. all the programming or deletion phases must be carried out with
the handset of the monitor raised.
Identification code programming
The identification code is programmed via an entrance panel (MASTER),
already configured and present on the system.
The monitor is supplied without associated identification code. To verify this
condition, press the lock release pushbutton and the monitor should emit
a triple "Beep".
Attention: during the video interphone identification code program-
ming you have 30 seconds from the moment you enter the program-
ming in the video interphone and the moment you press the call
push-button on the panel or you send the code.
Programming phase:
1) Lift the handset
2) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
3) Press and hold the lock release pushbutton "D" together with the
RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the lock release pushbut-
ton "D" pressed.
5) After 2 seconds the monitor emits a high tone, the monitor switches on
and communication is enabled with the panel.
6) Release the lock pushbutton "D".
7) On pushbutton entrance panels, press the call button for the monitor,
while on alphanumeric keypads, enter the call code and press pushbut-
ton " ".
8) If the system contains a monitor that already has the same associ-
ated identification code, the panel emits a low signal and the operation
should be repeated from point 2.
9) Otherwise the code is associated with the monitor, communication is
terminated and the monitor switches OFF.
Secondary identification code programming
Programming of the secondary identification code is only required when
more than one monitor is to be called by means of the same pushbutton
or call code. The monitors that ring at the same time are associated with
the same group. The "master" monitor is programmed first by means of the
"identification code programming" procedure described above, while the
additional group monitors are programmed with the secondary identification
code (see table shown in the wiring diagram section).
A maximum of three audio door entry units plus one group master can be
associated with the same group, without the need for programmer Type
950C or SaveProg .
In case monitors Petrarca are associated to the interphones, it is nec-
essary to add an additional power supply type 6923 for any possible
additional monitor. By using programmer type 950C or SaveProg it is
possible to program the activation of chime of all monitors and the
switching on of the "master" monitor. Before answering from a sec-
ondary video interphone from a secondary video interphone it is pos-
sible to switch the respective monitor on by means of the self-start
push-button " ".
Programming phase:
1) Lift the handset
2) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
3) Press and hold the lock release pushbutton "D" and self-start pushbut-
ton "E", together with the RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the other two pushbuttons
pressed (D end E).
5) After 2 seconds the monitor emits a high tone, the monitor switches on
and communication is enabled with the panel.
8
All manuals and user guides at all-guides.com
6) Release the lock release pushbutton "D" and self-start pushbutton "E".
7) On pushbutton entrance panels, press the call button for the "master"
8) When the secondary code is associated with the monitor the communi-
To know the number assigned see table shown in the wiring diagram sec-
tion.
Pushbutton programming
The monitor is fitted with three pushbuttons for the functions lock release,
self-start and the auxiliary service "stair light", which activates the 1st relay
of the 1st actuator (type 69RH), if connected to the system.
To change the operating mode of the self-start pushbutton and auxiliary ser-
vice "stair light" use programmer type 950C or SaveProg, with the exception
of assignment of the functions of intercommunicating calls and self-start
service to a specific panel.
During pushbutton programming the ringtone volume control must not be in
the ringtone mute position.
Intercommunicating call pushbutton programming "
Programming phase:
1) Raise the handset of the interphone/video interphone to call (when
2) Press and hold the RESET pushbutton "G" present below the monitor
3) Press and hold the additional pushbutton to make the intercommunicat-
4) Release the RESET pushbutton "G", keeping the call pushbutton
5) After 2 seconds the monitor emits a high tone, while the other inter-
6) Release the intercommunicating call pushbutton.
7) On the interphone/monitor called (with the 3-tone ring), press one of the
8) A high tone confirms the end of the procedure.
Repeat the same procedure for the other interphones/monitors and any
other intercommunicating call pushbuttons.
PROGRAMMING THE SELF-START PUSH-BUTTON TO A SPECIFIC
ENTRANCE PANEL
With this procedure it is possible to activate only push-button "
default push-button "
(master), as an alternative it can be programmed only by means of pro-
grammer 950C or SaveProg to activate the self-start of another entrance
panel (slave).
Programming phase:
1) Lift the handset
2) Press and hold the pushbutton "
3) Release the RESET pushbutton "G", keeping the pushbutton "E"
4) After 2 seconds the monitor emits a high tone.
5) Release the pushbutton "E".
6) On pushbutton entrance panels, press the call button for the monitor,
7) A high tone confirms the end of the procedure.
1) Press and hold the RESET pushbutton "G" present below the monitor
2) Press and hold the relative pushbutton to be reprogrammed together
3) Release the RESET pushbutton "G", keeping the other pushbutton
4) After 2 seconds the interphone emits a high tone.
monitor, while on alphanumeric keypads, enter the call code of the
"master" interphone and press pushbutton "
cation is terminated and the monitor switches off.
using series 8870, Giotto, Petrarca). With other versions of series
6600 (without handset) press and keep pressed the talk/listen
push-button .
(see Fig. 4) to be called.
ing call together with the RESET pushbutton "G".
pressed.
phone/monitor emits a 3-tone ascending scale.
programmed pushbuttons (such as lock, F1, F2 or actuator.).
" activates the self-start of the main entrance panel
together with the RESET pushbutton "G".
pressed.
while on alphanumeric keypads, enter the call code and press pushbut-
ton " ".
Restoring default values of pushbuttons.
Programming phase:
(see Fig. 4).
with the RESET pushbutton "G".
pressed.
".
" (P2)
". The
" to activate the self-start function
EN