Publicité
Les langues disponibles
Les langues disponibles
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.
WARNING
- DO NOT overfill the pool and / or allow people to lay over or sit on pool wall - DOING SO CAN CAUSE PERMANENT INJURY!
DRAIN pool to the proper level after a heavy rain.
TIP:
It will be much easier to install your pool if you unfold it and let it lay in direct sunlight for about 2 hours prior to installation. This will help to ensure a
wrinkle-free fit because the pool material will be more pliable allowing it to form into shape during installation.
WARNING
- VERY IMPORTANT! SITE MUST BE LEVEL, STABLE, COMPACTED SOIL.
• The pool must be assembled on a smooth and level site of firm soil that is free of stones, gravel, sticks, blacktop, or other oil base compounds.
Do not install pool on a wooden deck or any type of wooden surface. You cannot use sand and/or uncompacted soil to provide a level surface for this pool;
it will only wash out.
• FAILURE TO FOLLOW THE INSTRUCTIONS BELOW WILL CAUSE POOL TO COLLAPSE AND WILL VOID THE WARRANTY!
1. Select a level area, and completely remove all debris, twigs, stones, etc. DO NOT select an area under overhead electrical lines, trees, or within 15 feet of a house,
building, etc.
2. The pool shall be located a minimum distance of 6ft (1.83m) from any electrical receptacle.
3. All 125 volt, 15 and 20 ampere receptacles located within 20ft (6.0m) of the pool shall be protected by a ground fault circuit interrupter (GFCI).
The 20ft (6m) distance is measured via the shortest straight line distance the supply cord would follow without piercing a floor, wall, ceiling, doorway, window, or
other permanent barrier.
4. Contact your local utilities, checking that no underground cables, telephone lines, gas lines, etc. run beneath the area you have selected.
Setup Instructions
1. Carefully unfold the Quick Set
pool and inspect seams for manufacturing defects. With the inflatable ring on the top side, lay out the pool in the area selected,
®
making sure the bottom of the pool is both flat and round. If your pool included or you are going to purchase a filter/pump system, position the intake/ outlet fitting
locations so they are 10 to 21 feet from the electrical outlet you plan to use for the pool pump.
2. Inflate the top ring. Squeeze the base of the valve stem to open an internal check valve while inflating.
3. If your pool included a filter/pump system, following all instructions Installation of the filter pump.
NOTE: AFTER ABOUT 1-INCH OF WATER IS ON THE BOTTOM, STOP FILLING AND SMOOTH WRINKLES OUT OF THE BOTTOM OF THE POOL, WORKING
THEM FROM THE CENTER OUTWARD.
BE SURE FLOOR OF POOL IS ROUND AND FLAT. Next pull the outer wall out from under the top ring, all around the bottom of the pool, so that it fills evenly.
NOTE: IF MORE THAN 1-2 INCHES OF WATER COLLECTS ON ANY ONE SIDE BEFORE THE POOL STARTS FILLING IN THE CENTER, THE POOL IS NOT
LEVEL ENOUGH, AND MUST BE CORRECTED. SEE "SITE PREPARATION," ABOVE.
4. NOTE: THE WEIGHT OF THE WATER WILL PREVENT ADJUSTMENT AFTER THIS POINT.
5. Now, as you continue filling, the inflated ring will rise as the water deepens. Max. Water Level is the bottom seam of the inflatable ring; this information is printed on
the ring. Once this is done, refer back to the "Swimming Pool Filter System" owner's manual, and continue from Step "D" on through the rest of the installation if you
have a filter/pump system.
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8 AM to 5 PM Mon. thru Fri.
SETUP INSTRUCTIONS
1
MST. Extended operating days and hours during peak season requirements.
OWNER'S MANUAL
2
3
9
Publicité
