DOLD SAFEMASTER C BH 5910 Manuel D'instructions page 37

Technical Data
Input
Nominal voltage U :
N
Voltage range
at max. 5 % residual ripple:
Nominal consumption:
Control voltage on
S11, S13, S21, S23,
S31, S33, S41, S43,
48, 58:
Control current on
S12, S14, S22, S24,
S32, S34, S42, S44:
Min. voltage at
terminals S12, S14, S22,
S24, S32, S34 S42, S44:
Fusing:
Output
Contacts
BH 5910.03:
BH 5910.22:
Contact type:
Operating time typ. at U
N
Function Manual start
E-stop
Light curtains
Safety gates 45 ms (Simulation)
2-hand control 54 ms (Activation)
* TS = closing of gate
)
max. switch off time (reaction time)
Function
E-stop
Light curtains
Safety gates
2-hand control
Switching off when failure
in feedback circuit:
Nominal output voltage:
Switching of low loads:
Thermal current I :
th
Switching capacity
to AC 15
NO contact:
NC contact:
to DC 13 at 0,1 Hz:
Electrical life
to AC 15 at 2 A, AC 230 V:
Permissible switching
frequency:
Short circuit strength
max. fuse rating:
line circuit breaker:
Mechanical life:
Semiconductor outputs
Output (terminal 48 and 58):
Nominal output voltage:
All manuals and user guides at all-guides.com
DC 24 V
0,85 ... 1,15 U
N
max. 170 mA
(Semiconductor outputs not connected)
DC 23 V at U
N
4,5 mA at U each
N
DC 16 V
internal with PTC
3 NO contacts
2 NO contacts, 1 NC contact
The NC contact can only be used as
indicator contact.
Relay, forcibly guided
Auto start
Start Restart
45 ms 1,6 s 45 ms
45 ms 1,6 s 45 ms
90 ms (TS)*
28 ms
28 ms
28 ms
28 ms
max. 100 ms
AC 250 V
DC: see limit curve for arc-free operation
≥ 100 mV
5 A
3 A / AC 230 V IEC/EN 60947-5-1
2 A / AC 230 V IEC/EN 60947-5-1
8 A / DC 24 V IEC/EN 60947-5-1
10 5 switching cycles IEC/EN 60947-5-1
max. 1 200 switching cycles / h
6 A gG / gL IEC/EN 60947-5-1
C 8 A
10 x 10 switching cycles
6
transistor outputs, switching +
DC 24 V, max. 100 mA continuous
current, max. 400 mA for 0,5 s internal
short circuit, over temperature and
overload protection
Technical Data
General Data
Operating mode:
Temperature range
Operation:
Storage :
Altitude:
Clearance and creepage
distances
rated impuls voltage /
pollution degree:
EMC
Electrostatic discharge:
HF-irradiation:
Fast transients
on wires for power supply A1-A2: 2 kV
on signal and control wires:
Surge voltages
between
wires for power supply:
between wireand ground:
HF-wire guided:
Interference suppression:
Degree of protection:
Housing:
Terminals:
Housing:
Vibration resistance:
)
Shock proof:
Acceleration:
Impulse length:
Number of shocks:
Climate resistance:
Terminal designation:
Wire connection:
Wire fixing:
Mounting:
Weigth:
Dimensions
Width x height x depth:
37
Continuous operation
± 0 ... + 50 °C
- 25 ... + 85 °C
< 2000 m
4 kV / 2 (basis insulation) IEC 60664-1
8 kV (air) IEC/EN 61000-4-2
(according to test degree 3)
10 V / m IEC/EN 61000-4-3
IEC/EN 61000-4-4
2 kV IEC/EN 61000-4-4
1 kV IEC/EN 61000-4-5
2 kV IEC/EN 61000-4-5
10 V
Limit value class B EN 55011
according to IEC/EN 61496-1 (1997)
the unit has to be mounted in a control
cabinet with protection class 54
IP 40 IEC/EN 60529
IP 20 IEC/EN 60529
Thermoplastic with V0 behaviour
according to UL subject 94
according to IEC/EN 61496-1 (1997)
Amplitude 0,35 mm IEC/EN 60068-2-6
frequency 10 ... 55 Hz
10 g
16 ms
1000 per ax is on all 3 axes
0 / 050 / 04 IEC/EN 60068-1
EN 50005
1 x 2,5 mm 2 stranded wire with sleeve or
1 x 4 mm 2 solid or
2 x 1,5 mm 2 stranded wire with sleeve
DIN 46228-1/-2/-3/-4
Plus-minus terminal screws M3,5
box terminals with wire protection
DIN rail IEC/EN 60715
320 g
45 x 84 x 121 mm
BH 5910 / 200217 / 190A