Publicité
EN
Safety
DE
Sicherheit
ES
Seguridad
EN
Safety
•
Failure to follow these instructions may result
in personal injury, damage to the product and
property damage.
•
Always be aware of the danger of scalding
from hot water. Ensure users are aware of
the maximum temperature especially if the
temperature stop has been adjusted.
•
Never twist or kink the hose or otherwise
restrict the water flow whilst in use.
Getting started
•
Make sure you have all of the parts listed.
•
Make sure you have all of the tools required.
•
This tap must be installed by a suitably
competent person.
•
For domestic use only.
•
Check that the tap is suitable for your
water system.
•
The minimum supply pressure for this tap is
shown on the packaging.
•
It is important that supply pipes are flushed
before connecting the tap to ensure no pipe or
plumbing debris enters the tap.
•
If a combination boiler is installed turn off the
boiler before starting work.
•
Isolate the hot and cold water supply as close to
the tap connections as possible.
CAUTION: Do not overtighten fixings
as this may damage the product.
•
Ensure that the product is properly installed
before using.
•
When the installation is complete, turn the
water supply on and check for leaks at all
connection points.
•
TURN OFF WATER MAINS SUPPLY. The mains
stopcock is usually situated where the supply
enters the building.
•
It is also recommended that the water heating
arrangements are turned off.
•
Isolate the hot and cold water supply.
•
Operating Specification:
Hot Water Supply - Maximum. 85°C
Recommended 55-65°C
•
Operating Pressure:
Maximum 5 Bar
•
If you are in any doubt about installing
this product, consult a technically
TLS12985-08_195422_s6_s8 8Freestanding mixer -F100030_20191113 V30620 v5.indd 4
FR
Sécurité
RUS Безопасность
PT
Segurança
competent installer.
•
Operating pressures on hot and cold lines should
be kept as even as possible in order to ensure
the maximum effciency of the mixer.
•
When water pressure is higher than 5 bar a
pressure reducing valve (not supplied) must be
fitted before the mixer.
•
This product must be connected to a water
supply in accordance with the Water Supply
(Water Fittings) Regulations 1999, and UK Building
Regulations. If you are in any doubt about these
requirements, contact a qualified plumber, your
local Water Company or the Water Regulations
Advisory Service (WRAS).
Pull out and spring neck taps
•
Never leave pull out tap heads submerged in
your sink.
•
Warning from your Water Supplier.
•
This tap has an outlet on a flexible hose
which, if left immersed in water, could result in
contaminated water being drawn back into the
pipework if the supply pressure dropped. To
prevent contamination of drinking water in the
premises and in the water main, and to comply
with the legal requirements of the UK plumbing
regulations and byelaws, both hot and cold
water supplied to this tap must come from a
storage cistern.
•
If the distributing pipes feeding this tap from the
storage cistern have other outlets connected to
them, the outlet of this tap must be lower than
any of those other outlets.
•
If installed as a tap which is used for drawing
water for drinking, and the quality of water from
the storage cistern does not meet the standards
for drinking water, a separate tap supplied
with wholesome water must be provided for
drinking purposes.
Care & maintenance
•
Use warm soapy water and a soft damp cloth to
clean the surface of the product. Wipe dry with
a clean cloth.
•
Never use any solvents, scourers, abrasives,
bleach, acids, strong detergents, aggressive
chemical cleaners or solvent-type cleaning
solutions on the product.
•
Periodically check fixings and connections to
ensure there are no leaks.
•
Flexible supply hoses are fitted with mesh
filters to prevent debris from your water
supply damaging the tap. Over time these may
PL
Bezpieczeństwo
RO
Siguranță
TR
Emniyet
4
20/11/2020 14:03
Publicité
