Publicité
Les langues disponibles
Les langues disponibles
English
• Wire and picket fences cause extra string wear, even
breakage. Stone and brick walls, curbs, and wood may wear
string rapidly.
• Do not allow spool cap
other surfaces.
• In long growth, cut from the top down and do not exceed
12" (305 mm) high.
• Keep trimmer tilted toward the area being cut; this is the
best cutting area.
• The trimmer cuts when passing the unit from the left to
right. This will avoid throwing debris at the operator.
• Avoid trees and shrubs. Tree bark, wood moldings, siding,
and fence posts can easily be damaged by the string.
Cutting Line/Line Feeding
Your trimmer uses 0.065" (1.65 mm) diameter, ROUND nylon
line. During use, the tips of the nylon lines will become
frayed and worn and the special self-feeding spool will
automatically feed and trim a fresh length of line. Cutting
line will wear faster and require more feeding if the cutting
or edging is done along sidewalks or other abrasive surfaces
or heavier weeds are being cut. The advanced automatic
line feeding mechanism senses when more cutting line
is needed and feeds and trims the correct length of line
whenever it's required. Do not bump unit on ground in
attempt to feed line or for any other purposes.
Clearing Jams and Tangled Line (Fig. K)
WARNING:
the trimmer before making any assembly, adjustments or
changing accessories. Such preventive safety measures reduce
the risk of starting the appliance accidentally.
From time to time, especially when cutting thick or stalky
weeds, the line feeding hub may become clogged with
sap or other material and the line will become jammed as a
result. To clear the jam, follow the steps listed below.
CAUTION:
the cutting line protrudes beyond the trimming blade, cut it
off so that it just reaches the blade.
1. Remove the battery from the trimmer.
2. Press the release tabs
remove the spool cap from the spool housing
3. Pull the nylon line spool out and clear any broken line or
cutting debris from the spool area.
4. Place spool and line into spool cap with line "parked" in
slots provided.
5. Insert the line end through the appropriate hole in the
spool housing. Pull slack line through until it pulls out of the
holding slots.
6. Press the spool down GENTLY and rotate it until you
feel it drop into place and then push to snap into place.
(When in place, the spool will turn a few degrees left and
right freely).
7. Take care to keep the line from becoming trapped under
the spool.
8. Fit the spool onto the appliance as described in
Replacing Spool Assembly.
Replacing Spool Assembly (Fig. K, L)
WARNING:
recommended by CRAFTSMAN for use with this appliance
could be hazardous.
8
to drag on ground or
18
Remove the battery from
To avoid appliance damage, if
on the spool cap
, and
19
18
10
(Figure K).
The use of any accessory not
WARNING:
any accessory or attachment other than those recommended
by CRAFTSMAN on this trimmer. Serious injury or product
damage may result.
Reload nylon line (either bulk or prewound replacement
spool) as shown in this manual.
USE ONLY 0.065" (1.65 mm) DIAMETER ROUND NYLON
MONOFILAMENT LINE. Do not use serrated or heavier gauge
line, as they will overload the motor and cause overheating.
This line is available at your local dealer or authorized
service center.
1. Remove battery from appliance.
2. Press the release tabs
remove the spool cap from the spool housing
3. For best results, replace spool with CRAFTSMAN
Model # CMZST065.
4. If lever in base of housing becomes dislodged, replace in
correct position before inserting new spool into housing.
5. Remove any dirt and grass from the spool cap and
spool housing.
6. Unfasten the end of the cutting line and guide the line
into the eyelet.
7. Take the new spool and push it onto the boss
housing. Rotate the spool slightly until it is seated.
8. The line should protrude approximately 5-3/8" (136 mm)
from the housing.
9. Align the release tabs on the spool cap with the slots in
the spool housing.
10. Snap the spool cap back on by depressing release tabs
and pressing into spool housing.
11. Push the cap onto the housing until it snaps securely
into place.
nOTE: Make sure that cover is fully positioned, listen for
two audible clicks to ensure both release tabs are correctly
located. Power the appliance on. In a few seconds or less
you'll hear the nylon line being cut automatically to the
proper length.
nOTE: Other replacement parts (guards, spool caps, etc.)
are available through authorized service centers. To find
your local service location call: 1-888-331-4569 or visit
www.craftsman.com.
Rewinding Spool from Bulk Line (use only
0.065" [1.65 mm] ROUND diameter line) (Fig. A, M, N)
Bulk line is also available for purchase from your local
retailer. nOTE: Hand wound spools from bulk line are likely
to become tangled more frequently than CRAFTSMAN
factory wound spools. For best results, factory wound spools
are recommended.
1. Remove battery from appliance.
2. Remove the empty spool from the appliance as
described in Replacing Spool Assembly.
3. Remove any remaining cutting line from the spool.
4. Make a fold at the end of the cutting line at about 3/4"
(19 mm)
21
. Feed the cutting line into one of the line
anchoring slots
.
22
5. Insert the 3/4" (19 mm) end of the bulk line into the
hole
in the spool adjacent to the slot. Make sure the line
23
is pulled tight against the spool.
6. Wind the cutting line onto the spool in the direction of
the arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross.
Do not use any blades, or
on the spool cap
, and
19
18
10
(Figure K).
20
in the
Publicité
