Yamaha PLG100-DX Mode D'emploi page 41

* Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO AMOD DEPTH
By default, the Pitch Control effect is applied.
If the Multi Part parameter Rcv PITCH BEND CHANGE = OFF, that part
will not receive pitch bend messages.
1.6 Channel aftertouch
This message conveys the pressure after the key is played on the keyboard (for
an entire MIDI channel). The pressure can be controlled for each part. This
message will affect the notes currently playing.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Channel Aftertouch.
1.7 Polyphonic aftertouch
This message conveys the pressure after the key is played on the keyboard (for
individual note numbers). The pressure can be controlled for each part. This
message will affect the notes currently playing.
The effect of this message is determined by the following Multi Part param-
eters.
l. PAT PITCH CONTROL
2. PAT AMPLITUDE CONTROL
3. PAT LFO PMOD DEPTH
4. PAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv POLY AFTER TOUCH = OFF, that part will
not receive Polyphonic Aftertouch.
2. System exclusive messages
2.1 Parameter changes
This devices uses the following parameter changes.
[UNIVERSAL REALTIME MESSAGE]
1) Master Volume
[UNIVERSAL NON REALTIME MESSAGE]
1) General MIDI System On
[XG PARAMETER CHANGE]
1) XG System on
2) XG System parameter change
3) Multi Part parameter change
[PLG100-DX NATIVE PARAMETER CHANGE]
1) PLG100-DX System parameter change
2) PLG100-DX Multi Part parameter change
[DX PARAMETER CHANGE]
1) VCED parameter change
2) ACED parameter change
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
11110000 F0H = Exclusive status
= Universal Real Time
01111111 7FH
= ID of target device
01111111 7FH
= Sub-ID #1=Device Control Message
00000100 04H
= Sub-ID #2=Master Volume
00000001 01H
* 0sssssss SSH = Volume LSB
0ttttttt TTH = Volume MSB
= End of Exclusive
11110111 F7H
= Exclusive status
11110000 F0H
= Universal Real Time
01111111 7FH
= Device Number, xxx = don't care
0xxxnnnn XNH
00000100 04H = Sub-ID #1=Device Control Message
00000001 01H = Sub-ID #2=Master Volume
= Volume LSB
0sssssss SSH
= Volume MSB
0ttttttt TTH
= End of Exclusive
11110111 F7H
When received, the Volume MSB is reflected in the System Parameter MAS-
TER VOLUME.
* The binary expression Osssssss is expressed in hexadecimal as SSH.
The same applies elsewhere.
2.1.2 Universal non-realtime messages
2.1.2.1 General MIDI System On
11110000 F0H = Exclusive status
01111110 7EH = Universal Non-Real Time
= ID of target device
01111111 7FH
= Sub-ID #1=General MIDI Message
00001001 09H
= Sub-ID #2=General MIDI On
00000001 01H
= End of Exclusive
11110111 F7H
or
11110000 F0H = Exclusive status
= Universal Non-Real Time
01111110 7EH
= N:Device Number, X:don't care
0xxxnnnn XNH
= Sub-ID #1=General MIDI Message
00001001 09H
= Sub-ID #2=General MIDI On
00000001 01H
11110111 F7H = End of Exclusive
When this message is received, the SOUND MODULE MODE is set to XG,
and all data except for MIDI Master Tuning will be restored to the default value.
However this message will not be received when SOUND MODULE MODE =
C/M.
Since approximately 50ms is required to process this message, be sure to allow
an appropriate interval before sending the next message.
2.1.3 XG parameter change
This message sets XG-related parameters. Each message can set a single param-
eter.
The message format is as follows.
Exclusive status
11110000 F0H
YAMAHA ID
01000011 43H
0001nnnn 1NH N:device Number
01001100 4CH Model ID
0ggggggg GGH Address High
Address Mid
0mmmmmmm MMH
Address Low
0lllllll LLH
Data
0sssssss SSH
: :
11110111 F7H End of Exclusive
For parameters whose Data Size is 2 or 4, the appropriate amount of data will be
transmitted as indicated by Size.
2.1.3.1 XG System On
11110000 F0H Exclusive status
01000011 43H YAMAHA ID
0001nnnn 1NH N:device Number
01001100 4CH Model ID
00000000 00H Address High
00000000 00H Address Mid
01111110 7EH Address Low
00000000 00H Data
11110111 F7H End of Exclusive
When ON is received, the SOUND MODULE MODE changes to XG.
Since approximately 50ms is required to process this message, be sure to allow
an appropriate interval before sending the next message.
2.1.3.2 XG System Parameter Change
This message sets the XG SYSTEM block (see Tables <1-1> and <1-2>).
2.1.3.3 Multi Part Parameter Change
This message sets the Multi Part block (see Tables <1-1> and <1-3>).
2.1.4 PLG100-DX native parameter change (1)
This message sets parameters unique to the PLG100-DX. Each message sets a
single parameter. The message format is as shown below.
Exclusive status
11110000 F0H
YAMAHA ID
01000011 43H
N:Device Number
0001nnnn 1NH
Model ID
01100010 62H
0ggggggg GGH Address High
0mmmmmmm MMH Address Mid
Address Low
0lllllll LLH
Data
0vvvvvvv VVH
: :
End of Exclusive
11110111 F7H
For parameters whose Data Size is 2 or 4, the appropriate amount of data will be
transmitted as indicated by Size.
2.1.4.1 PLG100-DX System Parameter Change
This message sets the PLG100-DX SYSTEM block (see Tables <2-1> and <2-
2>).
Appendix
41