Emerson AVENTICS ST6-SM Instructions De Montage page 24

Switching point mode Two point mode
Qint.SPx and Qint.SPy are determined. As soon as the magnet has passed
Qint.SPx and Qint.SPy, the signal is 'high'. As soon as the magnet is below
Qint.SPx, the signal is 'low'. (Qint.SPx < Qint.SPy)
Qint.SPy
+ 25 mm
2
1
ON
ON
Qint.SPy
+ 25 mm
ON ON
Fig. 13: Switching point mode 'Two point mode'
1 Switching range
Switching point mode Cylinder switch mode
Within the width of the switching point, the switch signal is 'high'. The hysteresis
lies symmetrically around Qint.SP1.
The switch signal switches to 'high' as soon as the piston moves into the switch-
ing width and switches to 'low' as soon as the piston leaves the hysteresis.
+ 25 mm
2
2
OFF ON
+ 25 mm
2
2
OFF OFF
Fig. 14: Switching point mode 'Cylinder switch mode'
1 Width of the switching point
3 Direction of travel of the magnet
AVENTICS™ ST6-SM | R412028907-BAL-001-AA | English
Qint.SPx
OFF OFF
OFF
Qint.SPx
2
1
ON ON OFF
2 Direction of travel of the magnet
Qint.SP1
1 2
1 2
ON OFF OFF
Qint.SP1
1 2
1 2
ON ON OFF
2 Hysteresis
12 Disposal
Improper disposal will lead to pollution of the environment. Furthermore, the
materials can no longer be recycled.
Dispose of the product, the packaging and any escaping operating materials
u
in accordance with the applicable national regulations.
ON
13 Troubleshooting
13.1 Procedure
– 25 mm
OFF
Step 1: Check the system
3 In case of malfunctions, first check the system or the system part where the
2 u
product is installed. Check the following items:
• All connections
• Settings. See
Step 2: Check the product
ON
1. Make sure the system or system part is not under pressure or voltage.
2. Check the product based on the fault patterns described below.
3. Perform troubleshooting using the information under "Remedy".
If the malfunction cannot be eliminated as described under "Remedy": Disas-
– 25 mm
OFF
semble the product and return it. See
4. After the malfunction has been eliminated; Put the system or product back
3 into operation.
2
13.2 Malfunction types
Error
Green LED does not illumi-
nate
Sensor position is inaccurate Unfavorable installation posi-
End positions are lost
Both LEDs are flashing quickly Incorrect sensor configura-
The analog position indica-
tion outputs 10.5 V or 11 V
The position indication via IO-
Link outputs -32760 Digits1
ON
or 32760 Digits1
32764 is output via IO-Link
– 25 mm
OFF
14 Technical data
3
3
This section contains an excerpt of the most important technical data. Further
technical data can be found on the product page in the Emerson store.
General
ON
Dimensions
Cylinder design
Ambient temperature during operation
min. ... max.
– 25 mm
OFF
Performance data
3
3
Detection range
Readiness delay
Resolution, typ.
g 14. Technical data.
g 4.3 Returning the
Possible cause
No voltage or voltage below
limits
tion selected
The sensor is not yet com-
pletely taught-in to the actua-
tor
tion detected
Outside detection range
Outside detection range
Field strength insufficient
Specifications
32.5 mm x 5.8 mm x 4.8 mm
T-slot
–20 °C ... +70 °C
Specifications
50 mm: -25 mm ... +25 mm (deviations may occur
depending on the actuator)
0.15 s
IO-Link 0.01 mm
Analog output 0.013 mm
product.
Remedy
Check power supply, lines
and plug connections.
Reposition the product and
perform a voltage reset. See
g 6.3 Mounting the product.
Perform several strokes (> 5)
and set the end positions
again.
Perform a Factory reset. See .
Reposition the product. See
g 6.3 Mounting the product.
Reposition the product. See
g 6.3 Mounting the product.
Reposition the product. See
g 6.3 Mounting the product.
24