Oursson MG2000 Manuel D'instructions page 13

PRODUCT SET
Accessories for each model. Рiс. В
1
Pusher ................................................................ 1 pc.
2 Filling tray ........................................................... 1 pc.
3
Cutting block ....................................................... 1 pc.
4 Body ................................................................... 1 pc.
5 Perforated disk 8 mm holes ................................ 1 pc.
6 Perforated disk 5 mm holes ................................ 1 pc.
7 Perforated disk 3,2 mm holes .............................. 1 pc.
8
Locking attachment ............................................ 1 pc.
9 Blade .................................................................. 1 pc.
10 Screw .................................................................. 1 pc.
11 Sausage attachment (Sml) ..................................... 1 pc.
12 Sausage attachment (Midl) .................................... 1 pc.
13
Sausage attachment (Big) ..................................... 1 pc.
14 Locking ring ........................................................ 1 pc.
15 Separator ........................................................... 1 pc.
16 Parmesan grater attachment .............................. 1 pc.
17 Grater attachment (Sml) ..................................... 1 pc.
18
Grater attachment (Big) ...................................... 1 pc.
19 Slicer attachment (Big) ....................................... 1 pc.
20 Slicer attachment (Sml) ...................................... 1 pc.
21 Pusher ................................................................ 1 pc.
22 Cutting block ....................................................... 1 pc.
Pasta disks ......................................................... 3 pc.
23
Instructions manual ............................................ 1 pc.
ELEMENTS OF DESIGN, Рiс. С-1
Button to remove the cutting block
1
Control panel
2
Cord storage
3
Assembling the meat grinder, Рiс. C
For mince,
Pic. C-4
1. First, insert the screw
10
into the cutting block
2. Install the blade onto the
screw. Pic. C-2.
3. Install one of the disks
onto the screw
8 9 10
, ,
with blades.
4. Tighten the assembled cutting block with a locking attachment
5. Install cutting block 3
in the meat grinder, turn it counterclockwise and lock until it
clicks.
6. Connect the opening of the cutting block with the filling tray
7. Place the pusher 1 into the filling tray
All manuals and user guides at all-guides.com
For sausages,
Pic. C-5
.
3
2. Install the screw onto the separator
3. Install onto the separator
the required attachment
11 12 13 .
, ,
4. Install the locking ring .
14
2
1 .
UTILIZATION, Рiс. C
Control panel, Рiс. C-3
- ON/OFF power button.
The power is on when the button is in the upper
position (•).
- START/STOP button. Press START/STOP button
to start the meat grinder engine.
- REVERSE button. If something got stuck in
re
the meat grinder, turn it off by pressing START/
STOP button. Press and hold REVERSE
button, so that the cutting screw begin to rotate
into the opposite direction, pushing the stuck
product out.
- UNLOCK button. Use this button to UNLOCK
the motor for the meat grinder to work properly
again.
Before first use, wipe the device with a soft, dry cloth.
The rest of the parts wash with warm water and
detergent. Before assembling or disassembling the
device and / or removing attachments, make sure that
the device is unplugged.
The blades are very sharp, be careful.
Automatic engine protection
Automatic protection works to protect the engine
from overheating and to avoid breakage. In case
when automatic protection turned on, the device will
stop and buttons on the control panel won't work. Let
the device cool for 5-10 minutes, then press and hold
дbutton to unlock.
For For pasta
meatballs, preparation,
Pic. C-5 Рiс. С-7
2. Place one of
15 .
disks on the
auger 23 .
8 , turning it clockwise.
.
For vegetables,
Pic. C-6
1. Insert the required
nozzle 16 17 18 ,
, ,
into the cutting
19 20
,
block 22 .
2. Secure the cutting
block 22 in the meat
grinder, turn counter-
clockwise and lock
until it clicks.
3. Place the pusher
21
into the cutting block
22 .
13