Publicité
Les langues disponibles
Les langues disponibles
o
oi
o
r io
or i
Default value=2.
Value
[2-26]
1
2
3
i
i
i
i co
o
oi
o
r io
o
Default value=3.
Value
[2-27]
1
2
3
i
i
i
i co
o
r co
io i i
control adaptor (DTA104A61/62)
If the system needs to be running under power consumption
i i
io co
i io
i
i
i
fi
tion that will be applied for step 1. The level is according to
the table.
Default value=3.
limitation.
Value
[2-30]
1
2
3
4
5
6
7
8
o
r co
io i i
control adaptor (DTA104A61/62)
If the system needs to be running under power consumption
i i
io co
i io
i
i
i
fi
tion that will be applied for step 2. The level is according to
the table.
Default value=1.
or i
Value
[2-31]
1
2
3
35
r i
c io o r
ir
i i
Start time automatic low noise
operation (approximately)
8:00 p.m.
10:00 p.m. (default)
12:00 a.m.
c io
i
i
i
Start time automatic low noise
operation (approximately)
6:00 a.m.
7:00 a.m.
8:00 a.m. (default)
c io
i
i
io
i
r
r
i
i
o
o
r co
io i i -
or i
c io o r
ir
Power consumption limitation
(approximately)
io
i
r
r
i
i
o
o
r co
io i i -
c io o r
ir
i i
io
Power consumption limitation
(approximately)
orc
i
o
r co
io i i
o
r
co ro
or i r
consumption limitation)
If the system always needs to be running under power
consumption limitation conditions, this setting activates and
fi
o
r co
applied continuously. The level is according to the table.
Default value=0 (OFF).
Value
Restriction reference
[2-32]
0
Function not active (default)
1
o o
2
o o
or i
c io o r
oor
i
i
Indoor units fan speed limitation related to connection ca-
pacity and outdoor air temperature for energy saving.
Default value=0.
Value
Indoor unit fan tap setting
[2-34]
Fan speed is limited to L tap when indoor units
0
c
ci
In heating mode, fan speed is limited to L tap
1
i
oor
i c
Fan speed follows a setting of the remote controller
2
(not limited by indoor units connection capacity).
See the service manual for other indoor unit fan tap settings.
i
i
r
c
i
Default value=1.
In case the outdoor unit is installed in the lowest position
(indoor units are installed on a higher position than outdoor
units) and the height difference between the highest indoor
i
o
oor
i
c
o
c
o
Other changes/limitations to the circuit apply, for more infor-
io
i i
c
ic coo i
Default value=0.
Value
[2-45]
0
No technical cooling available. (default)
1
Technical cooling available.
This setting is not applicable to multi Branch Selector unit.
For more information about this setting, refer to the service manual.
r
r
r
ri
Default value=0.
Value
[2-47]
0
1
2
3
4
5
6
7
3P362438-5N English
io o
r io
ir
o
r or
o
r
io i i
io
i
i
i
ir
i i
io
ci
i
i i
io
o
Description
r co r o
r io
T
target
e
Auto (default)
37°F (3°C)
43°F (6°C)
45°F (7°C)
46°F (8°C)
48°F (9°C)
50°F (10°C)
52°F (11°C)
Publicité
