Elvox ES82 Guide De Connexion page 24

GB
PROBLEMS - CAUSES AND SOLUTIONS
PROBLEM
When a command is made via the radio
control or the key-switch, the gate does
not open or the motor
does not start
The gate does not open when a command
is made via the radio control, but works
when the key-switch is used
The gate starts moving, but then stops
N.B. - If the problem persists, contact your Dealer or your nearest Service Centre
GUARANTEE FOR THE ELVOX PRODUCTS
GENERAL CONDITIONS
1) The above mentioned conventional guarantee leaves unprejudiced the consumer rights arising from the application of the EU Directive
99/44/CE as far as the legal guarantee is concerned and is ruled by the D.L. n. 24 dated 02.02.2002 published in G.U. 57 dated
18.05.2002.
2) The ELVOX product guarantee lasts 24 months from the purchase date and includes the repair with free replacement of parts with de-
fects or material vices.
The product vice denunciation must be communicate within 2 months from the vice detection, therefore for a total coverage period of
26 months.
3) Elvox Costruzioni Elettroniche S.p.A. allows the guarantee by the Assistance Centres, for products presented or sent complete with the
guarantee document filled in in all its parts and accompanied by the fiscal bill proving the purchase date.
4) The guarantee certificate does not cover:
- appliances not working because of a not correct repair carried out by not qualified personnel.
- parts presenting normal wear and tear.
- bad or different use of the appliance not in accordance with the instruction manual and the wiring diagrams enclosed with the applian-
ces;
- all damages caused by natural calamities, tampering, and incorrect supply voltage;
- operation vices arising from an incorrect installation carried out disregarding the documentation supplied by Elvox S.p.a.
- damages caused during the transportation by third parties not under the Elvox S.p.A. liability.
Post guarantee technical assistance
The assistance out of guarantee includes the costs concerning the spare parts, manpower and fees for the call.
Directive 2002/96/EC (WEEE)
The crossed-out wheelie bin symbol marked on the product indicates that at the end of its useful life, the product must be handled
separately from household refuse and must therefore be assigned to a differentiated collection centre for electrical and electronic
equipment or returned to the dealer upon purchase of a new, equivalent item of equipment.
The user is responsible for assigning the equipment, at the end of its life, to the appropriate collection facilities.
Suitable differentiated collection, for the purpose of subsequent recycling of decommissioned equipment and environmentally com-
patible treatment and disposal, helps prevent potential negative effects on health and the environment and promotes the recycling
of the materials of which the product is made. For further details regarding the collection systems available, contact your local waste
disposal service or the shop from which the equipment was purchased.
Risks connected to substances considered as dangerous (WEEE).
According to the WEEE Directive, substances since long usually used on electric and electronic appliances are considered dange-
rous for people and the environment. The adequate differentiated collection for the subsequent dispatch of the appliance for the re-
cycling, treatment and dismantling (compatible with the environment) help to avoid possible negative effects on the environment and
health and promote the recycling of material with which the product is compound.
All manuals and user guides at all-guides.com
PROBLEMS - CAUSES AND SOLUTION
LIKELY CAUSE
230 Volt mains power failure
Emergency STOP enabled
Blown fuse
Motor power supply cable faulty or
disconnected
Something is blocking the photocell,
or it is not working properly
The radio control has not been memorised
or its battery is exhausted
The motor thrust is insufficient
24/36
SOLUTION
Check the main switch
Check switches or STOP command
status. If not in use, check whether the jum-
per is on the STOP contact input on the
switchboard
Replace it with another of the same value
Connect the cable to the relevant
terminal or replace it
Check the wiring, remove any obstacles
Carry out the radio control recognition pro-
cedure on the radio receiver or replace the
battery with a new one
Adjust the value with the THRUST trimmer
on the switchboard