i-onik Hometec WS-100 Manuel page 29

5.2.4 Connecting Auto Dialler to your home telephone
• A phone line must be connected to the Dialler in order for the Auto Dialler to work.
• Open the battery compartment to reveal 2 sockets for telephone cables
• Connect the "Line" socket to your wall telephone jack.
• Connect the "Phone" socket to your telephone, which then will share the phone line with the Auto
Dialler.
Normal telephone functions are interrupted only during an emergency, when the Auto Dialler takes
control of the phone line.
5.2.5 Troubleshooting
• If the LCD screen shows "FAIL" this means that the telephone line is not properly attached or phone
connections are invalid. Please check the connection.
• If the recording quality is low. Please record again in a quiet environment
with your mouth close to the microphone. (2-6 inches).
5.3 Quick Start Guide
Step 1:
To ENTER Press
Enter SETUP
SETUP mode
PIN (Default PIN is '1234').
mode for
Press
prior to any
program-
ming
To RECORD Press and hold
a message on the screen to start the recording.
Speak clearly into the microphone to record the mes-
sage Recording will finish when you press
after 20 seconds of recording.
Example message:
This is a security alert from [your name] at [your
address]. After listening to this message, please press
the hash key (#) and press '1' to listen in to this
address or '3' to speak.
Step 2:
To PLAYBACK Press and release
Under SETUP
your message
mode
To CHECK Press
PHONE
Press
NUMBERS
To ENTER/
Press
STORE Repeat this step to choose which phone number you
PHONE wish to program (1-8).
NUMBERS
Press
mum 15 digits).
If number entered incorrectly, press
number and re-enter the phone number digits
Press
To ERASE Press
a stored Repeat this step to choose which phone number you
phone wish to erase (1-8).
number
Press
20
All manuals and user guides at all-guides.com
to activate the keyboard Enter the 4-DIGIT
to go into SETUP mode.
key for 2 seconds until REC shows
again or
to playback the recorded message.
(Display will show '1' for the first number).
again for checking subsequent phone numbers.
(Display will show '1' for the first number)
and enter the phone number digits (maxi-
to clear the
to finish.
(Display will show '1' for the first number).
then to confirm erasing.
Press (Display will show '1' for the first number)
To program
the number Repeat this step until the display shows
of DIALLING
Press then enter the number of cycles you wish the
CYCLES
Auto Dialler to run through (select 1 to 9 cycles, default
cyle is 3 times) and press
To CHANGE Press (Display will show '1' for the first number)
the 4-DIGIT Repeat this step until the display shows
PIN
Press and enter a new 4-DIGIT PIN.
Re-enter the new 4-DIGIT PIN and press
Press to enter ALERT mode.
To ENTER
ALERT MODE
Step 3:
To activate When triggered by an external sensor, the i.onik
Under ALERT EMERGENCY Dialler immediately starts dialling through the stored
mode DIALLING telephone numbers according to the number of dialling
cycles you have programmed.
To activate Press and
PANIC button on the KEYFOB remote.
DIALLING
To CANCEL If the EMERGENCY or PANIC DIALLING has been
EMERGENCY activated in error, the dialling can only be cancelled by
or PANIC disconnecting the mains power to the Auto Dialler and
DIALLING disconnecting the battery backup.
5.4. Instructions for the Recipient
Note: There are several things that your call recipients should know in order to successfully receive
and terminate an emergency call from your Auto Dialler. Therefore make sure your Auto Dialler
recipients understand what to do when they receive your emergency call by passing them a copy of
these instructions.
5.4.1 To START speakerphone conversation
• After having full listened to the recorded message, press the hash key (#), to confirm that the
message is NOT merely delivered to a voice mail
• Activate the "Listening-in" function by pressing "1" and "Speaking-in" function by pressing "3".
These can only be used when the call recipient presses the Hash key (#)
• Time out period is 60 seconds and recipients can extend either the listening time or speaking time
by pressing "1" or "3" accordingly. With each pressing, a further 60 seconds will be allowed by the
Auto Dialler.
The conversation will be disconnected if the Auto Dialler receives no instruction.
5.4.2 To STOP the emergency message of the existing call AND all the
remaining calls.
• The Auto-Dialler will continue dialling the numbers until the call is answered
• The recipient can stop the Auto Dialler by waiting until the message has finished, and pressing (#).
This will stop the Auto Dialler from calling this and all remaining phone numbers.
• As this termination stops the Auto Dialler from calling any more phone numbers, the recipient must
know the exact situation before terminating it.
5.4.3 To DISCONNECT all calls after conversation
• Once the speakerphone conversation is over, the recipient should disconnect the call by pressing
(#) instead of just hanging up the phone. This will terminate the connection for all existing call and
the remaining calls.
.
to confirm.
.
to confirm.
® Auto
simultaneously or press the PANIC
21