i-onik Hometec WS-100 Manuel page 23

A. Adjusting Exit Delay
The default setting of the Smart Panel allows the user 20 seconds to exit the property before the
alarm is ARMED. However, this Exit Delay can be adjusted to between 10 and 60 seconds as follows:
Keys Description
1 (1234/ You must be in STANDBY
4-digit mode before adjusting the
PIN) Exit Delay.
+
2 (1234/ Enter the default PIN "1 2
4-digit 3 4" OR your new 4-digit
PIN) PIN for setting followed
+ by
.
Press then (as
3
many times as required)
+
to set the new Exit Delay.
4 Press to complete the
setting
.
B. Adjusting Entry Delay
The default setting of the Smart Panel allows the user 30 seconds to enter the property and DISARM
the alarm before it is triggered. However, this Entry Delay can be adjusted to between 10 and 60
seconds as follows:
Keys Description
1 (1234/ You must be in STANDBY
4-digit mode before adjusting the
PIN) Entry Delay
+
8
All manuals and user guides at all-guides.com
Note
To make sure you are in STANDBY mode:
- Enter the default PIN " 1 2 3 4 " OR your new 4-digit
PIN
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
The Smart Panel will display the below image:
- When is pressed the first time the Smart Panel
flashes with the number of seconds currently set
for the Exit Delay (The factory default setting is 20
seconds).
- Each time is pressed the Exit Delay is increased
by a further 10 seconds between the adjustable
range of 10 to 60 seconds.
- The Exit Delay time on the LCD display will flash
until the setting is completed.
Confirm the setting and return the Smart Panel to
STANDBY by pressing
.
Note
To make sure you are in STANDBY mode:
- Enter the default PIN " 1 2 3 4 " OR your new 4-digit
PIN
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
2 (1234/ Enter the default PIN "1 2
4-digit 3 4" OR your new 4-digit
PIN) PIN for setting followed
+ by
.
Press then (as
3
many times as required)
+
to set the new Entry
Delay.
4
Press to complete the
setting .
C. Adjusting the Alarm Duration
The default setting of the Smart Panel gives an alarm duration of 1 minute after being triggered.
However, this alarm duration can be increased up to 6 minutes:
Keys Description
1 (1234/ You must be in STANDBY
4-digit mode before adjusting the
PIN) Alarm Duration.
+
2 (1234/ Enter the default PIN "1 2
4-digit 3 4" OR your new 4-digit
PIN) PIN for setting followed
+ by
.
Press then (as
3
many times as required)
+
to set the new Alarm
Duration.
4 Press to complete the
setting
.
D. Muting the Audible Countdown
When the Smart Panel is ARMED the audible countdown (beeper) can be silenced by pressing the
MUTE button, during the countdown. To reactivate the audible countdown (beeper) simply press the
MUTE button again.
The Smart Panel will display the below image:
- When is pressed the first time the Smart Panel
flashes with the number of seconds currently set for
the Entry Delay (The factory default setting is
30 seconds).
- Each time the Entry Delay is increased by a
further 10 seconds between the adjustable range of
10 to 60 seconds.
- The Entry Delay time on the LCD display will flash
until the setting is completed.
Confirm the setting and return the Smart Panel to
STANDBY by pressing
.
Note
To make sure you are in STANDBY mode:
- Enter the default PIN " 1 2 3 4 " OR your new 4-digit
PIN
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
The Smart Panel will display the below image:
- When is pressed the first time the Smart Panel
flashes with the number of minutes currently set for
the Alarm Duration (The factory default setting is
1 minute).
- Each time is pressed the alarm duration is
increased by a further minute up to a maximum of
6 minutes.
- The Alarm Duration on the LCD display will flash
until the setting is completed.
Confirm the setting and return the Smart Panel to
STANDBY by pressing
.
9