Publicité
Les langues disponibles
Les langues disponibles
2
Battery voltage low level Plug in
AC adapter to the DC socket in
the back of the Smart Panel
2.3 Understanding the battery and AC adaptor icon
Battery icon shows power status
Battery icon shows when the AC power supply is unplugged or
below:
interrupted.
9V battery functions as BACK-UP only and the
Full -
means LOW BATTERY.
High -
The LCD backlight flashes YELLOW for 30 seconds and
Middle -
will blink until the new battery is replaced or the mains power
Low -
supply (with AC adaptor) is plugged in.
When the AC adaptor to the Smart Panel is connected to a
AC Adaptor icon
wall socket, the AC symbol will appear.
The backlight will be 'ON' for 10 seconds while the AC adapter
connects to the power supply.
3.1 Programming your new 4-digit PIN
The Wire-free i.onik
Smart Panel is supplied with a default PIN of "1234". This can be changed to
®
your own personalised PIN, or your own personalised PIN can be changed, as follows:
Keys
Description
1
(1234/
You must be in STANDBY
4-digit
mode before programming
PIN)
your new 4-digit PIN
+
2
(1234/
Enter the default PIN "1 2
4-digit
3 4" OR your new 4-digit
PIN)
PIN for setting followed
+
by
3
Press
followed by
4
New
Enter the new 4-digit PIN
4-digit
followed by
PIN +
5
New
Re-enter new PIN for
4-digit
followed by
for final
PIN +
confirmation
6
All manuals and user guides at all-guides.com
The main power supply (with AC adaptor) must be
plugged in at all times, with the 9V battery functio-
ning as back-up power supply only, when the
mains power supply is interrupted
Note
To make sure you are in STANDBY mode:
- Enter the default PIN "1 2 3 4"
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
The Smart Panel will display the below image:
- Press
then "1" to set the new PIN
- The Smart Panel will display the below image:
- LCD display
flashes with "1"
- Enter the new 4-digit PIN
- Press
to confirm
- LCD display
flashes with "2"
- Re-enter the new 4-digit PIN
- Press
for final confirmation
(One beep indicates that you entered a valid PIN, two
beeps indicate that an invalid operation was performed).
3.2 Transmitting an emergency (Panic) alarm
3.2.1 Using the Panic alarm
Pressing
&
mit an alarm signal to the Smart Panel, activating the siren, and transmitting an alarm signal to any
optional response devices (Auto Dialler & Outdoor Bell Box), to request emergency assistance.
To disarm the Panic alarm
On the Smart Panel: Enter your 4-digit PIN followed by
On the Key Fob Remote Control: Press
3.2.2 Using the Panic alarm without activating the siren
If you are forced to disarm the system, enter the Duress Password to stop the siren from sounding.
symbol
The Smart Panel will then silently transmit an alarm signal to the optional response devices (Auto
Dialler & Outdoor Bell Box) to request emergency assistance.
Duress Password:
Enter the default 4-digit PIN +
OR
Enter your personalised 4-digit PIN+
3.3 Operating different modes
The system has 4 operating modes (STANDBY, ARM, ALERT, and HOME) to suit individual require-
ments.
These modes can be set as follows:.
3.3.1 STANDBY mode
If in STANDBY mode, the Smart Panel is prepared for mode selection.
Keys
1
(1234/
4-digit
PIN)
+
3.3.2 ARM mode
When in ARM mode, the Smart Panel siren will sound and the Smart Panel flashes RED every
1.5 seconds when the system is triggered.
ARM mode default setting:
Sensor
Door/Window Sensor
Door/Window Sensor
Motion Sensor
buttons together on the Keypad or Key Fob Remote Control will immediately trans-
to exit from the Panic alarm.
(
+
) +
+
Description
Note
You must be in STANDBY
To make sure you are in STANDBY mode:
mode before turning to
- Enter the default PIN "1 2 3 4"
ARM mode
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
Zone
1
2
8
to exit from the Panic alarm.
Status (MODE)
ARM
ARM
ARM
7
Publicité
