Publicité
Les langues disponibles
Les langues disponibles
E. Arming the system
On the Key Fob Remote Control: Press
On the Smart Panel: First make sure the Smart Panel is in STANDBY mode, and then ARM the system
by taking the following steps:
Keys
Description
1
(1234/
You must be in STANDBY
4-digit
mode before turning to
PIN)
ARM mode.
+
2
(1234/
Enter 4-digit PIN, press
4-digit
and
for ARM
PIN)
mode.
+
+
When in ARM mode, the Smart Panel flashes red every 5 seconds, acting as a deterrent to potential
intruders. However, if an intruder is detected the panel continuously and rapidly flashes red.
Once an intrusion has occurred (with the zone triggered under ARM status), the alarm siren will
sound and the Smart Panel flashes red every 1.5 seconds with the triggered zone indicated. After the
initial triggering, the alarm will immediately sound, without delay, if any other sensors are triggered.
F. Disarming the system
• On the Smart Panel: Enter your 4-digit PIN followed
• On the Key Fob Remote Control: Press
G. Zone settings
Programming each zone in ARM mode:
Keys
Description
1
(1234/
You must be in STANDBY
4-digit
mode before turning to
PIN)
ARM mode
+
10
All manuals and user guides at all-guides.com
to ARM the system.
Note
To make sure you are in STANDBY mode:
- Enter the default PIN " 1 2 3 4 " OR your new 4-digit
PIN
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
Exit delay: up to 15 seconds
- There is a 15 second exit delay time with a visual
and audible (beeping) countdown before the system
is armed.
(Press MUTE to disable the beeping countdown,
press MUTE again to resume the beeping)
- If the Zone is enabled, a number will appear as
displayed in the image below:
- The system will then enter ARM mode after
15 seconds.
by to disarm the system.
to disarm the system.
Note
To make sure you are in STANDBY mode:
- Enter the default PIN " 1 2 3 4 " OR your new 4-digit
PIN
- Press
- The Smart Panel will display the image below when
you are in STANDBY mode:
(One beep indicates that you entered a valid PIN,
three beeps indicate that an invalid operation was
performed).
2
(1234/
Enter 4-digit PIN for
4-digit
setting followed by
.
PIN)
+
Press
then
(as
3
many times as required)
+
to set the new Exit Delay.
4
Press
to complete the
setting.
H. Triggers in ARM mode
Example: Zone 1 trigger
Step
Description
Note
1
Under the "ARM" Mode
The Smart Panel will display the below image:
2
System trigger
One beep indicates that the system is triggered.
3
Entry delay 30 seconds
There are 30 seconds of entry delay time with a visual
countdown for disarming.
Once an intrusion has occurred (zone triggered under ARM
status), the alarm siren will sound for 1 minute and the
Smart Panel flashes red every 1.5 seconds with the trigge-
red zone indicated, until the system is disarmed.
To disarm the system, enter the 4-Digit PIN or press
the remote control.
4
Return to ARM mode after
After the initial triggering, the alarm will immediately
the initial triggering
sound, without delay, if any other sensors are triggered.
3.3.3 ALERT mode
If in Alert mode, the Smart Panel chime will sound and the Smart Panel flashes green every
1.5 seconds with the triggered zone indicated, when the system detects a visitor in the protected
area.
ALERT mode default setting:
Sensor
Zone
Door/Window Sensor
1
Door/Window Sensor
2
Motion Sensor
8
A. Entering ALERT mode
to activate.
• On the Key Fob Remote: Press
The Smart Panel will display the below image:
- Toggle 1, 2, 3, 4, 5, 6, 7, 8 to turn each zone ON or
OFF
- If no number appears, the zone is turned OFF
- The Smart Panel will display the below image:
Confirm the setting and return the Smart Panel to
STANDBY by pressing
Status (MODE)
ALERT
ALERT
ALERT
on
11
Publicité
