Wahl Moser 1592 Q Mode D'emploi page 9

Operation
Preparation
Keep the packaging material for safe storage or transport
later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power supply.
f Only operate the appliance with the voltage stated on
the nameplate.
Charging the battery
1. Connect the appliance plug on the plug-in transformer to the
charging stand socket (Fig. 2ⓐ).
Battery overcharging is prevented thanks to intelligent
charge management.
2. Connect the plug-in transformer to the mains socket (Fig. 2ⓑ).
3. Switch off the appliance using the on/off switch (Fig. 3ⓑ).
4. Place the appliance in the charging stand (Fig. 2 ).
·
During charging, the charging indicator flashes at evenly
spaced intervals.
·
After the appliance has been removed from the charging
stand, the display goes out (power saving mode).
5. As soon as the battery is fully charged, the charging indicator
flashes at a different rate (10 on / 1 off).
Battery operation
1. Switch on the appliance using the on/off switch, and switch off
after use (Fig. 3ⓐ/ⓑ).
In case of insufficient maintenance of the blade set, the
operating time can be reduced considerably.
Operation
Cutting with attachment comb
The appliance can also be operated with an attachment comb.
f The attachment comb has 5 detent positions for adjusting the cut-
ting length.
f The further the attachment comb is pushed onto the blade set, the
shorter the cutting length.
The cutting length can be adjusted from 3 mm (Fig. 5ⓐ) to
6 mm (Fig. 5ⓑ).
Attaching/removing the attachment comb
1. Slide the attachment comb onto the blade set (Fig. 4ⓐ) in the
direction of the arrow until it locks in place.
2. The attachment comb can be removed by pushing it in the direc-
tion of the arrow (Fig. 4ⓑ).
Maintenance
Warning! Injuries and material damage due to incorrect
handling.
f Switch off the appliance before cleaning it or performing
any maintenance and disconnect it from the mains.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and
accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
·
Accessories are available from our dealer.
·
Spare parts are available from our service centre.
f Remove the attachment comb (Fig. 4ⓑ) and lift the blade set out
of the housing (Fig. 6ⓐ). Use the cleaning brush to remove any
cut hairs from the housing opening and from the blade set (Fig. 7).
The cleaning lever can also be pressed. This allows the cut hairs that
accumulate between the bottom blade and the top blade to be eas-
ily removed using the cleaning brush (EASY CLEANING).
f The charging contacts on the appliance and on the charging stand
should always be kept clean.
f Only wipe the appliance with a soft, slightly damp cloth.
f Oil the blade set with blade set oil (Fig. 8).
f For a good and long-lasting cutting performance, it is
important to oil the blade set frequently.
f If the cutting performance deteriorates after long use
despite regular cleaning and oiling, the blade set should
be replaced.
Changing the blade set
1. Slide the blade set off the housing in the direction of the arrow
(Fig. 6ⓐ). Remove the blade set.
2. Replace the blade set by hooking it into the housing and pressing it
down until it clicks into position (Fig. 6ⓑ).
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
9
ar