Error And Information Messages - Futurelight MH-860 Mode D'emploi

- Adjusting the default positions of colour, gobo and effect wheels
By this function you can calibrate and adjust the colour, gobo and effect wheels to their standard/right
positions. Use the [Up] and [Down] keys to browse through the adjusting menu - the display shows step by
step these messages: " PAn, Tilt, SPEd, Col1, Col2, PriS, SGob, rGob, Grot, IriS, Foc, Stro, dimr, FCAL
" by which you can adjust the fixture to the required / desired position (0-255) before the function calibration.
Then when the positioning is finished use the last "FCAL" function (Fixture calibration).
1. Calibration via the control board
Press [Enter] and the [Up] and [Down] keys in order to display the following messages: "Col1, Col2, PriS,
SGob, rGob, Grot " for very smooth function calibration. Select one of them, press [Enter] and use the [Up]
and [Down] keys in order to adjust their right value from 0 to 255. Then press [Enter] to confirm or [Mode]
to cancel and return to the menu. This can be repeated for each calibration parameter if it is required. When
the calibration is finished, it is necessary to use the "ArES" function in order to write the calibration values to
the memory (EEPROM) and to make a reset in order to check the newly adjusted positions of the colour,
gobo and effect wheels. When the reset of the fixture is finished, the display will show the "FCAL" message.
Press [Enter] to repeat the calibration or [Mode] to return to the "AdJ" menu.
2. Calibration via the external controller
Press [Enter] and the [Up] and [Down] keys in order to display the following messages: "Colo, EFEC,
rGob, Grot" - calibration parameters. Select one of them and press [Enter].
Now you can calibrate the colour, gobo and effect wheel by your controller. The DMX calibration protocol is
described in the table mentioned below.
DMX Calibration protocol:
'0;

&KDQQHO
&2/
&$/,%5$7,21
)XQFWLRQ
  
'0;
&KDQQHO
35,60
)XQFWLRQ
67$1'$ 5'
35272&2/
After having calibrated required functions press [Enter] to confirm (or [Mode] to cancel and return to the
menu without reset by the "ArES" function) and use the "ArES" function in order to write the calibration
values to the memory (EEPROM) and to make a reset in order to check the new adjusted positions of the
colour, effect and rot. gobo wheels and gobo indexing.
This message appears if you try to switch on the lamp within 5 minutes after having switched it off (the lamp
is too hot). The message will appear on the display if the lamp doesn't ignite within 28 seconds. The MH-860
will store this information and automatically ignite the lamp when the 5 minutes period has expired.
Caution: Please note that this function is disabled if the lamp light sensor is switched off (function "EnSn").
 
&2/ 6*2%
&$/,%5$7,21 &$/,%5$7,21
     
6022 7+ 0,&5267( 3 029( 0(17
 
67$ 7,& 52 7$7,1*
*2%26 *2%26
67$1'$ 5' 67$1'$ 5'
35272&2/ 35272&2/

Error and information messages

 
5*2% *527
&$/,%5$7,21 &$/,%5$7,21
     
 
*2% 2
,5,6
527$7,21
67$1'$ 5' 67$1'$ 5'
35272&2/ 35272&2/
48
 
 &2/2856 
67$1'$ 5'

35272&2/
 
)2&86 6752 %(
67$1'$ 5' 67$1'$ 5'
35272&2/ 35272&2/

&2/2856 
67$1'$ 5'
35272&2/

',00(5
67$1'$ 5'
35272&2/