Glass Cleaning; Cleaning Out The Ashes; Cleaning The Flue; Majolicas (If Present) - Nordica VERONA XXL Manuel Utilisateur

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

gLAss CLEANINg

Thanks to a specific inlet of secondary air, the accumulation of dirty sediments on the glass-door is reduced with efficacy. Nevertheless this can
never be avoided by using solid fuels ( particularly wet wood ) and it has not to be understood as a defect of the appliance.
IMPORTANT: THE CLEANINg Of THE sIgHT gLAss MUsT BE CARRIED OUT ONLY AND EXCLUsIVELY WITH COLD DEVICE TO
AVOID THE EXPLOsION Of THE sAME.
For the cleaning, it is possible to use specific products or a wet newspaper paper ball passed in the ash to rub it. DO NOT UsE
CLOTHs, ABRAsIVE OR CHEMICALLY AggREssIVE PRODUCTs BY CLEANINg THE HEARTH gLAss.
The correct lighting phase, the use of proper quantities and types of fuels, the correct position of the secondary air regulator, enough draught
of the chimney-flue and the presence of combustion air are the essential elements for the optimal functioning of the appliance and for the
cleaning of the glass.
BREAk Of gLAssEs: Given that the glass-ceramic glasses resist up to a heat shock of 750°C, they are not subject to thermal
shocks. Their break can be caused only by mechanic shocks (bumps or violent closure of the door, etc.).
THEREfORE, THEIR REPLACEMENT Is NOT INCLUDED IN THE WARRANTY.

CLEANINg OUT THE AsHEs

All the devices are equipped with a hearth grating and an ash drawer for the collection of the ashes
It is suggested to empty periodically the ash drawer and to avoid it fills completely in order not to overheat the grating. Moreover, it is
suggested to leave always 3-4 cm of ash in the hearth.
CAUTION: THE AsHEs REMOVED fROM THE HEARTH HAVE TO BE sTORED IN A CONTAINER MADE Of fIRE-REsIsTANT
MATERIAL EQUIPPED WITH AN AIR-TIgHT COVER. THE CONTAINER HAs TO BE PLACED ON A fIRE-REsIsTANT fLOOR,
fAR fROM fLAMMABLE MATERIALs UP TO THE sWITCHINg Off AND COMPLETE COOLINg.

CLEANINg THE fLUE

The correct lighting phase, the use of proper quantities and types of fuels, the correct position of the secondary air regulator, enough draught
of the chimney-flue and the presence of combustion air are the essential elements for the optimal functioning of the appliance.
THE DEVICE SHOULD BE COMPLETELY CLEANED AT LEAST ONCE A YEAR OR EVERY TIME IT IS NEEDED (in case of bad working and low yield).
AN EXCESSIVE DEPOSIT OF SOOT CAN CAUSE PROBLEMS IN THE DISCHARGE OF SMOKES AND FIRE IN THE FLUE.
THE CLEANINg MUsT BE CARRIED OUT EXCLUsIVELY WITH COLD EQUIPMENT. THIS OPERATION SHOULD BE CARRIED
OUT BY A CHIMNEY SWEEPER WHO CAN SIMULTANEOUSLY PERFORM AN AUDIT OF THE FLUE (checking of possible deposits).
During the cleaning, it is necessary to remove the ash drawer and the smoke deflectors from the device in order to ease the cleaning of the
soot. The deflectors can be easily extracted from their seats since they are not fastened using screws. Once the clearing has been carried out,
place them back in their seats
CAUTION: THE LACk Of THE DEfLECTORs CAUsEs A sTRONg DEPREssION, WITH A TOO fAsT COMBUsTION, AN
EXCEssIVE CONsUMPTION Of WOOD WITH RELATED OVERHEATINg Of THE DEVICE.

MAjOLICAs (If PREsENT)

La NORDICA s.p.A.has chosen majolica tiles, which are the result of high-quality artisan work. As they are completely carried out by hand,
the majolica may present crackles, speckles, and shadings. These characteristics certify their precious origin.
Enamel and majolica, due to their different coefficient of dilatation, produce microcrackles, which show their authentic feature.
FOR THE CLEANING OF THE MAJOLICA WE SUGGEST YOU TO USE A SOFT AND DRY CLOTH;
If YOU UsE A DETERgENT OR LIQUID, THE LATTER MIgHT sOAk IN AND HIgHLIgHT THE CRACkLEs PERMANENTLY.

PRODUCTs MADE Of NATURAL sTONE (If PREsENT)

NATURAL STONE HAS TO BE CLEANED WITH VERY THIN ABRASIVE PAPER OR WITH AN ABRASIVE SPONGE. DO NOT UsE ANY CLEANSER
OR FLUID.

VARNIsHED PRODUCTs (If PREsENT)

After some years of product use a change in the varnished details colour is totally normal. This is due to the considerable temperature range
the product is subject to whenever in use and to the varnish ageing of time passing by.
ATTENTION: BEFORE ANY POSSIBLE APPLICATION OF THE NEW VARNISH, DO CLEAN AND REMOVE ALL THE TRACES FROM
THE SURFACE WHICH HAS TO BE VARNISHED.

ENAMELLED PRODUCTs (If PREsENT)

For the cleaning of enamelled surfaces use soap water or NOT AggREssIVE and NOT CHEMICALLY abrasive detergents.
AFTER THE CLEANING DO NOT LET SOAPY WATER OR ANY CLEANSER DRY BUT REMOVE THEM IMMEDIATELY.
DO NOT UsE sANDPAPER OR sTEEL WOOL.
34
11).
(Picture
ENGLISH
Picture
8.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Rosa xxlRosa l

Table des Matières