Oster PRO 1200 Guide De Démarrage page 6

Learning About The Oster Pro
1200 Blender
1. F iller Cap / 2 Ounce Measuring Cup: – Allows
you to add ingredients during use. Also allows
you to open to allow steam to escape when
blending hot foods.
2. Jar lid – Seals the blender jar.
3. Jar – 6-cup Dishwasher Safe Boroclass
jar withstands Thermal shock OR 8-Cup Break
Resistant BPA-Free Tritan Plastic.
TM
Blade Assembly – With locking feature to secure
blade assembly to threaded jar bottom. Seals the
jar to the blade for leak-proof operation.
4. S ealing Ring :
5. B lade – Creates a forward and reverse action
when the Programmed Settings are in use.
6. T hreaded Jar Bottom With Locking Lever –
Advanced design for simple assembly to jar.
7. M otor Base – Holds the jar securely. Contains
a powerful, reversible, variable speed motor.
8. Control Panel
a. Power Button ( ) – Turns the product On
and Off.
b. P re-Programmed Settings: Use for flawless
results at the touch of a button. Select the
desired setting and watch the Oster Pro
1200 cycle through the program, spinning
the blade forward and backwards for expert
results at the touch of a button. Unit will
shut after running through the cycle.
Select From:
Green/ Frozen Smoothies
Food Chop / Salsa
Milkshakes
c. Manual Controls: Select from
Low-Med-High
d. P ulse button – Press to pulse and
release to stop.
e. Stop Button: Press to stop any cycle or
manual control setting.
French_BLSTMB Series_16EFM1.indd 6-7
All manuals and user guides at all-guides.com
TM
1
TM glass
TM
a
6
Using The Oster Pro
Before you use the product for the first time, separate the lid, filler cap and blade from
the jar. Wash in warm, soapy water, or top rack in the dishwasher. Rinse and dry well.
CAUTION: Blade is sharp, handle with care.
2
Blade Assembly
Locking
Sealing Ring
3
1. Place Blade into Threaded Jar Bottom (Fig.1).
2. Place sealing ring over blade assembly. Carefully press
and tuck sealing ring into locking groove (Fig2).
3. Ensure the locking sealing ring is fully and evenly tucked
4
in place and holding the blade assembly to the threaded
jar bottom. For correct assembly see (Fig3).
4. I nstall the Integrated Blade Assembly onto the Jar. Turn clockwise to tighten.
B e sure the Integrated Blade Assembly is tightened to the jar before using.
5
NOTE: For proper installation onto Blender Motor base, make sure locking
lever rotates past the anti-rotation tabs on the Blender jar or smoothie cup.
See (Fig4).
6
5. Put the ingredients into the jar.
6. Secure the lid and filler cap.
7. Place the jar onto the base.
8. P lug the power cord into a standard household
120/127-volt, 60 hz. AC outlet. You are now ready
7
to start.
Using the Pre-Programmed Settings
8
1. P ress the ( ) power button to turn the product on. The power light will
blink, indicating the product is active and ready to use. The light will stay on
when the motor is running.
2. S elect and Press the desired Pre-Programmed Setting Button:
- "Green/Frozen Smoothie"
- "Food Chop/Salsa"
- "Milkshakes"
3. To change your selection, press Stop followed by another Pre-Programmed
Setting button ("Frozen Drinks & Shakes" or "Food Chop")
4. Once the program is finished the product automatically stops. Please note:
b
You may press the "Stop" button to cancel the program at any time. The
c
blinking blue light indicates that the blender is ready.
) power button to turn the product off. This product is pre-
d 5. Press the (
programmed to turn off automatically if not used for a period of several
e
minutes. All lights will turn off when the unit automatically powers down.
1200 Blender
TM
Threaded Jar
Blade Bottom with
Fig1
locking lever
7
Fig2
Incorrect Correct!
Fig3
Fig4
2/15/16 9:05 AM