Peg-Perego GT3 Notice D'emploi page 18

located under the seat (fig_a). Slip the hose
off the pump (fig_b) and screw it onto the
opposite end of the pump (fig_c). Remove
the cap from the tire (fig_d) and fasten the
end of the pump hose (fig_e).
_ Before using the stroller for the first time, you
are advised to inflate the tires to a pressure of 25
P.S.I./1.7 bar.
2 6 SHOCK ABSORBERS: all the wheels are
equipped with shock absorbers. The rear
wheels have adjustable shock absorbers.
You can choose from "HARD" for soft terrain,
such as sand and lawns, "SOFT" for rough
surfaces, such as gravel and cobble stones,
and "MEDIUM" for smooth, firm surfaces. To
adjust the shocks on the rear wheels, turn the
knob to choose one of the three settings. It is
recommended to adjust both rear wheels to
the same setting.
2 7 LEVERAGE BOARD: The rear leverage board
helps the mother push the stroller over
slightly uneven ground.
GANCIOMATIC SYSTEM
Ganciomatic is a quick, practical system that
allows you to attach the Navetta XL and
Primo Viaggio car seat (available separately)
to the stroller with the Ganciomatic
connectors.
2 8 GANCIOMATIC CONNECTORS ON THE
STROLLER: To raise the Ganciomatic
connectors on the stroller, lift the fabric
covering in the corners of the seat. Raise
the two Ganciomatic connectors, which will
automatically move outwards.
_ To lower the connectors, do the opposite.
The Navetta XL and Primo Viaggio car seat
can be attached to the GT3 in stroller mode,
with the backrest attached, or in GT3 Naked
mode (chassis version).
To convert the GT3 into a chassis version
GT3 Naked:
2 9 Put the backrest in the second position
and remove both of the side ridges that are
holding it up (fig_a). Hold down both of the
buttons at the bottom of the backrest (fig_b)
and lift it up (fig_c). Before you attach the
Navetta XL or Primo Viaggio car seat, raise the
rear part of the Ganciomatic base (fig_d).
_ To convert the chassis back into a stroller, go
through the same steps in reverse order.
3 0 (fig_a) GT3 + PRIMO VIAGGIO
To attach the car seat to the stroller or chassis:
_ Apply the brakes on the stroller.
_ Raise the Ganciomatic connectors on the
stroller.
_ Put the front bar in the first position.
All manuals and user guides at all-guides.com
_ If they are attached, remove the hood
_ Position the car seat so that it is facing the
_ To remove the car seat from the stroller,
(fig_b) GT3 + NAVETTA XL
To attach the Navetta XL bassinet unit to the
_ Apply the brakes on the stroller.
_ Raise the Ganciomatic connectors.
_ Raise the leg rest on the stroller or chassis to
_ Remove the front bar.
_ If they are attached, remove the hood
_ Place the Navetta XL on the Ganciomatic
_ Press on the sides of the Navetta XL with both
_ To remove the Navetta XL from the stroller,
3 1 REMOVING THE WHEELS: to remove the
3 2 FOLDING UP: before folding up the stroller,
3 3 REMOVABLE SEAT COVER: unbutton the sack
3 4 Pull the leg divider strap up from under the seat
ACCESSORY RANGE
3 5 BORSA: diaper-changing bag with pad for
3 6 MOSQUITO NET which can be attached to
- 18 -
from the stroller and completely lower the
backrest.
person pushing and push it down until it
clicks.
consult the instruction manual for the car
seat.
stroller or chassis:
the highest position.
from the stroller and completely lower the
backrest.
connectors of the stroller, with the head end
of the bassinet unit on the opposite side to
the handle of the stroller.
hands until it clicks into place.
consult the instruction manual for the
bassinet unit.
rear wheels press the button (arrow_a) and
pull the wheels off the sides of the stroller
(arrow_b). To remove the front wheel, press
the button on the rear ledge (arrow_c) and
pull the wheel off (arrow_d).
set the front wheels to stationary. If the hood
is mounted, loosen the braces. To fold the
stroller up, press button number 1 (fig_a)
using your right hand. Using your left hand,
grab the handle, press button number 2
(fig_b) and lift up the handle (fig_c). To
complete the folding, turn and fasten the
safety hook (fig_d).
from the seat (fig_a) and slip the sack off the
footrest (fig_b). Detach the sack from the
armrests (fig_c).
(fig_a), unbutton the side tabs from the backrest
(fig_b) and slip the tabs off the backrest (fig_c).
Then remove the sack.
changing baby's diaper. Attaches to the
stroller.
hood.