Publicité
Les langues disponibles
Les langues disponibles
Operation
5. Set the driving mode switch (05/1) to F (For-
ward) or R (Reverse).
6. Slowly press the driving pedal (10/1) down
until the desired driving speed is reached.
Stopping the ride-on mower
1. Press down the brake pedal (09/1) until the
mower comes to a standstill and hold it there.
2. Set the driving mode switch (05/1) to N (Neu-
tral).
3. Press the locking lever (08/1) upwards to ac-
tivate the parking brake.
4. Release the brake pedal.
5. Turn the safety key (07/1) to red (OFF posi-
tion).
6. Now you can get off the operator's seat.
6.5
Switching the mower mechanism on
and off
Requirements: The ride-on mower has been
started and the driving mode switch (05/1) is set
to N (Neutral) or F (Forward).
Switching on the mower mechanism
1. Pull the push/pull switch (03/1) upwards.
Switch off mower mechanism
1. Push the push/pull switch (03/1) downwards.
6.6
Setting the cutting height
1. Pull the cutting height adjustment lever (11/1)
towards the operator's seat to disengage it.
2. Move the adjustment lever to adjust the cut-
ting height in steps (for the cutting heights,
see technical data):
■
Downwards: for low cutting height.
■
Upwards: for high cutting height.
3. Push the adjusting lever outwards to engage.
NOTE Always lock the lever in the selected
position so that the mower mechanism is fixed
and does not move unexpectedly.
6.7
Driving at constant speed
Switching on constant speed
1. Press the driving pedal (10/1) down until the
desired driving speed is reached.
2. Press the CCS button (04/1).
3. Take your foot off the drive pedal. The ride-
on mower travels at a constant speed.
493389_b
Switching off constant speed
■
Press the brake pedal (09/1).
OR:
■
Press the drive pedal (10/1).
OR:
■
Press the CCS button (04/1).
6.8
Mowing backwards
WARNING! There is an accident risk
when reverse mowing! Risk of collision with
persons and objects behind the ride-on mower.
Serious injuries are possible.
■
Pay attention to the area behind you when
mowing in reverse.
■
Only mow in reverse when it is necessary to
do so.
Requirements: The ride-on mower has been
started and the driving mode switch (05/1) is set
to F (Forwards).
Switching on reverse mowing
1. Pull the push/pull switch (03/1) upwards to
switch on the mower mechanism.
2. Set the cutting height (see chapter 6.6 "Set-
ting the cutting height", page 43).
3. Press the RMO button (04/2).
4. Set the driving mode switch (05/1) to R (Re-
verse).
5. Slowly press the driving pedal (10/1) down
until the desired driving speed is reached.
When doing so, keep a close eye on the sur-
roundings at the rear.
Switching off reverse mowing
■
When you want to go forwards again: Set the
driving mode switch to F (Forwards).
OR:
■
To continue reversing with the mower mech-
anism switched off: Push the push/pull
switch (03/1) downwards.
6.9
Emptying the grass catcher
NOTE An audible signal sounds when the
grass catcher is full. The catcher should be emp-
tied now if not before.
The ride-on mower is equipped with a manually
operated grass catcher with telescopic lever.
■
The grass catcher can be emptied from the
operator's seat.
■
If the grass catcher is folded up or unhinged
when the mower mechanism is switched on,
43
Publicité
