Vimar Elvox GIOTTO Serie Manuel Pour Le Raccordement Et L'emploi page 9

Pressing a disabled push-button, the "chime excluded" LED "H" will flash to
indicate this operation mode.
Deleting all settings.
Programming phase:
This procedure is advised when you want to change the ID of an inter-
phone/monitor previously programmed and you do not want keep the ope-
ration programming of the appliance.
1) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
2) Press and hold the self-start pushbutton
RESET pushbutton "G".
3) Release the RESET pushbutton "G", keeping the self-start pushbutton
"E" pressed.
4) After 2 seconds the monitor emits a continuous tone for two seconds.
5) Release the self-start pushbutton "E".
6) During the continuous tone, press the lock release pushbutton "D".
If the deletion procedure is successful, when the lock release tab is pressed
once more the interphone emits a triple "Beep".
EN
OPERATION
Calls from an entrance panel, intercommunicating calls and door calls are
differentiated by means of different tones.
Door calls.
Calls from entrance panels do not follow the pressed pushbutton but are
generated inside the monitor. The call interval is 1 s of ringtone and 2 s
of pause repeated twice (default value set on panel). To answer, raise the
handset. If the handset is already raised during the call, replace and raise
it again. The call answer time (30 s) and the conversation time (2 minutes
by default) are set in the panel parameters. When the conversation time
"E" together with the
has elapsed, the user can continue without replacing the handset if a new
call is made within 10 s from the same panel.
Intercommunicating call.
Lift the monitor handset and press the intercommunicating button, if pro-
grammed, for the interphone/monitor to be called. On the handset of the
monitor calling, a call tone will ring (if the call is enabled) or an engaged
tone (if not enabled). On the called monitor the ringtone starts sequentially
at intervals of 1 s ringing and 4 s pause. The maximum duration of the call
is 30 s (6 cycles). To answer the call, simply raise the handset; the ma-
ximum duration of the conversation is 5 minutes. When the conversation
time has elapsed, the user can continue without replacing the handset if a
new call is made within 10 s. Calls from the panel have priority over inter-
communicating calls.
Denied calls.
The variator located below the monitor (Fig. 4) enables modification to
the call volume or to mute the signal. Call mute is indicated by permanent
illumination of the red LED. If calls are made to the monitor when the call
mute is enabled, they are denied. A denied call causes the red Led to
briefly switch off according to the number of times calls are denied (maxi-
mum 4 denied calls). The signal is repeated every 10 s (approx.). Deletion
of denied calls is by: reenabling the ringtone, resetting the monitor or a
system power failure. On the panel, a denied call is indicated by means of
a dissuasion tone (a series of "Beeps" at 100ms intervals with a pause of
100ms for a total of 5 seconds). The message "Do not disturb" also appears
on panels with display.
Lock Button
The lock button of each device works in the following manner.
- Device with handset at rest
- Device with handset raised but not engaged in a conversation
- Device with handset raised and engaged in an internal conversation
- Device with handset raised and engaged in an external conversation or
In practice a lock is always activated except when the handset is raised
and you immediately press the lock button. This can also be taken to the
standard case if the system has no porter switchboard and the Switchboard
flag is set on NO.
which it has spoken or from which it has been called.
to switchboard if the Switchboard flag is YES. Otherwise it goes back
to the first case.
as in the first case.
called from entrance panel lock
spoken with or from which it has been called.
lock to the last entrance panel with
to the entrance panel being
call
9