Vimar Elvox GIOTTO Serie Manuel Pour Le Raccordement Et L'emploi page 8

PROGRAMMING
There are three monitor programming modes: assignment of an identifica-
tion code or call code (indispensable), assignment of a secondary identifi-
cation code (for monitors associated with a master monitor), programming
of pushbuttons for auxiliary services and intercommunicating calls (when
necessary).
Programming must be performed with the system switched on, without
active communication and only after connecting the interphones/monitors
to the system and programming the panels.
N.B. all the programming or deletion phases must be carried out with
the handset of the monitor raised.
Identification code programming
The identification code is programmed via an entrance panel (MASTER),
already configured and present on the system.
The monitor is supplied without associated identification code. To verify
this condition, press the lock release pushbutton and the monitor should
emit a triple "Beep".
Attention: during the video interphone identification code program-
ming you have 30 seconds from the moment you enter the program-
ming in the video interphone and the moment you press the call
push-button on the panel or you send the code.
Programming phase:
1) Lift the handset
2) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
3) Press and hold the lock release pushbutton "D" together with the
RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the lock release pushbut-
ton "D" pressed.
5) After 2 seconds the monitor emits a high tone, the monitor switches on
and communication is enabled with the panel.
6) Release the lock pushbutton "D".
7) On pushbutton entrance panels, press the call button for the monitor,
while on alphanumeric keypads, enter the call code and press pushbut-
ton " ".
8) If the system contains a monitor that already has the same associa-
ted identification code, the panel emits a low signal and the operation
should be repeated from point 2.
9) Otherwise the code is associated with the monitor, communication is
terminated and the monitor switches OFF.
Secondary identification code programming
Programming of the secondary identification code is only required when
more than one monitor is to be called by means of the same pushbutton
or call code. The monitors that ring at the same time are associated with
the same group. The "master" monitor is programmed first by means of the
"identification code programming" procedure described above, while the
additional group monitors are programmed with the secondary identification
code (see table shown in the wiring diagram section).
A maximum of three audio door entry units plus one group master can be
associated with the same group, without the need for programmer Type
950C or SaveProg .
In case monitors Petrarca are associated to the interphones, it is ne-
cessary to add an additional power supply type 6923 for any possible
additional monitor. By using programmer type 950C or SaveProg it is
possible to program the activation of chime of all monitors and the
switching on of the "master" monitor. Before answering from a secon-
dary video interphone from a secondary video interphone it is possi-
ble to switch the respective monitor on by means of the self-start
push-button " ".
Programming phase:
1) Lift the handset
2) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
3) Press and hold the lock release pushbutton "D" and self-start pushbut-
ton "E", together with the RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the other two pushbuttons
pressed (D end E).
5) After 2 seconds the monitor emits a high tone, the monitor switches on
and communication is enabled with the panel.
6) Release the lock release pushbutton "D" and self-start pushbutton "E".
8
7) On pushbutton entrance panels, press the call button for the "master"
monitor, while on alphanumeric keypads, enter the call code of the
"master" interphone and press pushbutton "
8) When the secondary code is associated with the monitor the communi-
cation is terminated and the monitor switches off.
To know the number assigned see table shown in the wiring diagram
section.
Pushbutton programming
The monitor is fitted with three pushbuttons for the functions lock release,
self-start and the auxiliary service "stair light", which activates the 1st relay
of the 1st actuator (type 69RH), if connected to the system.
To change the operating mode of the self-start pushbutton and auxiliary
service "stair light" use programmer type 950C or SaveProg, with the
exception of assignment of the functions of intercommunicating calls and
self-start service to a specific panel.
During pushbutton programming the ringtone volume control must not be
in the ringtone mute position.
Intercommunicating call pushbutton programming "
Programming phase:
1) Raise the handset of the interphone/video interphone to call
(when using series 8870, Giotto, Petrarca). With other versions of
series 6600 (without handset) press and keep pressed the talk/li-
sten push-button .
2) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4) to be called.
3) Press and hold the additional pushbutton to make the intercommunica-
ting call together with the RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the call pushbutton pres-
sed.
5) After 2 seconds the monitor emits a high tone, while the other inter-
phone/monitor emits a 3-tone ascending scale.
6) Release the intercommunicating call pushbutton.
7) On the interphone/monitor called (with the 3-tone ring), press one of
the programmed pushbuttons (such as lock, F1, F2 or actuator.).
8) A high tone confirms the end of the procedure.
Repeat the same procedure for the other interphones/monitors and any
other intercommunicating call pushbuttons.
PROGRAMMING THE SELF-START PUSH-BUTTON TO A SPECIFIC
ENTRANCE PANEL
With this procedure it is possible to activate only push-button "
default push-button " " activates the self-start of the main entrance panel
(master), as an alternative it can be programmed only by means of pro-
grammer 950C or SaveProg to activate the self-start of another entrance
panel (slave).
Programming phase:
1) Lift the handset
2) Press and hold the pushbutton "
together with the RESET pushbutton "G".
3) Release the RESET pushbutton "G", keeping the pushbutton "E" pres-
sed.
4) After 2 seconds the monitor emits a high tone.
5) Release the pushbutton "E".
6) On pushbutton entrance panels, press the call button for the monitor,
while on alphanumeric keypads, enter the call code and press pushbut-
ton " ".
7) A high tone confirms the end of the procedure.
Restoring default values of pushbuttons.
Programming phase:
1) Press and hold the RESET pushbutton "G" present below the monitor
(see Fig. 4).
2) Press and hold the relative pushbutton to be reprogrammed together
with the RESET pushbutton "G".
3) Release the RESET pushbutton "G", keeping the other pushbutton
pressed.
4) After 2 seconds the interphone emits a high tone.
5) Release the pushbutton to restore to default and then press again.
".
" (P2)
". The
" to activate the self-start function
EN