SOEG-L-Q20
Lichtleitergerät
Anschluß der Kunststoff-Lichtleiter
1.) Mit dem Schneidewerkzeug der Lichtleiter auf die gewünschte
Länge abschneiden.
2.) Klemmbügel öffnen.
3.) Faser bis zum Anschlag in den Faserhalter einführen
(Widerstand beim Einführen am O-Ring muß überwunden
werden).
4.) Klemmbügel schließen.
Tastbetrieb: Schaltpunkt einstellen statisch
1.) Faser auf Objekt ausrichten. LED gelb und LED grün leuchten.
2.) Taste ca. 3 s drücken bis beide LED´s gleichzeitig blinken.
Sobald beide LED´s gleichzeitig blinken ist der Schaltpunkt erfasst.
3.) Objekt aus dem Erfassungsbereich entfernen.
4.)Taste ca. 1 s drücken (Hintergrund wird eingelernt). Die grüne
LED blinkt kurz und beginnt zu leuchten, die Schaltpunkte werden
gespeichert, der Sensor ist betriebs bereit.
Schaltpunkt nur mit einem Objekt einstellen
1.) Faser auf Objekt ausrichten. LED gelb und LED grün
leuchten.
2.) Taste ca. 3 s drücken bis beide LED´s gleichzeitig blinken.
Sobald beide LED´s gleichzeitig blinken ist der Schaltpunkt
erfasst.
3.) Objekt im Erfassungsbereich lassen und Taste nochmals
1 s drücken. Die grüne LED blinkt kurz und beginnt zu
leuchten, der Schaltpunkt wird gespeichert, das Gerät ist
betriebsbereit.
Lichtschrankenbetrieb: Empfindlichkeit einstellen statisch (nur bei
transparenten Objekten erforderlich)
1.) Sender auf Empfänger ausrichten. Beide LED´s leuchten.
2.) Taste ca. 3 s drücken bis beide LED´s gleichzeitig blinken.
Sobald beide LED´s gleichzeitig blinken ist der Schaltpunkt
erfasst.
3.) Objekt in den Erfassungsbereich bringen.
4.) Taste ca. 1 s drücken.
a:) Die grüne LED blinkt kurz und beginnt zu leuchten, die
Schaltpunkte werden gespeichert, der Sensor ist
betriebsbereit.
b:) Beide LED´s blinken gleichzeitig: der Sensor kann das
Objekt nicht erfassen, es werden keine Schaltpunkte
gespeichert.
Empfindlichkeit einstellen bei laufendem Prozess
1.) Faser auf Objekt ausrichten. LED grün an, LED gelb
undefiniert.
2.) Im Lichtweg befindet sich nur der laufende Prozess;
Taste ca. 3 s drücken bis beide LED´s gleichzeitig blinken.
3.) Taste erneut drücken, bis mindestens 1 Prozesszyklus im
Lichtweg stattgefunden hat.
Die grüne LED blinkt kurz und beginnt zu leuchten, die
Schaltpunkte werden gespeichert, der Sensor ist betriebs
bereit.
Ausgangsfunktion einstellen (Schließer/Öffner)
1.) Taste ca. 13 s drücken. LED´s blinken
abwechselnd
2.) Taste loslassen, grüne LED blinkt.
3.) Während die grüne LED blinkt wird bei jedem Tastendruck
die Ausgangsfunktion invertiert Dies wird durch die gelbe
LED angezeigt. Wenn die Taste während 10 s nicht
betätigt wird, ist die aktuelle Ausgangsfunktion
gespeichert. Der Sensor ist betriebsbereit.
Originalzustand / Maximale Empfindlichkeit (default)
1.) Ohne Objekt im Erfassungsbereich Taste ca. 3 s drücken
bis beide LED´s gleichzeitig blinken.
2.) Ohne Objekt im Erfassungsbereich Taste ca. 1 s drüc
ken. Sensor ist auf maximale Empfindlichkeit
eingestellt.
Steuerleitung (ET)
+UB
- gleiche Funktion wie Taste
-UB
- Eingabesperre (Taste ohne Funktion)
offen
- Normalfunktion
Warnung
Verwenden Sie nur Netzteile mit sicherer
elektrischer Trennung der Betriebspannung
nach IEC 742 / EN 60742 / VDE 0551 mit mind.
4 kV Isolationsfestigkeit (PELV). Schaltnetzt-
eile nach EN 60950 / VDE 0805 sind zulässig.
Warnung
Nicht für den Einsatz als Sicherheitsbauteil!
Elektrische Spannung! Vor Arbeiten an der
Elektrik: Spannung ausschalten.
Änderungen vorbehalten / All rights for alterations reserved / sous réserve de modifications
Festo AG & Co. KG, Postfach D-73726 Esslingen, Phone: +49/711/347-0
Fibre optic amplifier
Connection of fibre optics
1.) Cut the fibre optics with an appropriate cutter to the desired
length.
2.) Open the quick release lever.
3.) Insert the fibre optic as far as possible (pass resistance
due to ring).
4.) Close the quick release lever.
Proximity mode: Sensitivity setup
1.) Line up the fibre to the object. Yellow LED and green LED are on.
2.) Press the button 3 s until both LED´s are flashing synchro-
nously. (The first threshold is teached).
3.) Put the object out of the scanning area.
4.) Press the button 1 s (learning of backround).
The green LED flashes and stays on: the second threshold is
teached, the sensor is ready to operate.
Sensitivity setup only with object
1.) Line up fibre to the object. Yellow LED and green LED
are on.
2.) Press the button 3 s until both LED´s are flashing synchro
nously. (The first threshold is teached).
3.) Leave the object in the scanning area, press the button for
1 s. The green
LED flashes and stays on, the second treshold is teached,
the sensor is ready to operate.
Through beam mode: Sensitivity setup (necessary for transparent
objects only)
1.) Line up transmitter to the receiver. Both LED´s are on.
2.) Press the button 3 s until both LED´s are flashing
synchronously. (The first threshold is teached).
3.) Put the object into the scanning area.
4.) Press the button 1 s.
a:) The green LED flashes and stays on: the second
threshold is teached, the sensor is ready to operate.
b:) Both LED´s are flashing synchronously: the sensor can
not detect the object, no thresholds are teached.
Dynamic sensitivity setup at a running process
1.) Line up the fibre to the object. Green LED on, yellow LED
is undefined.
2.) The chosen running process must be the only thing in the
scanning area! Press the button 3 s until both LED´s are
flashing synchronously.
3.) Press the button for a minimum of one process cycle is
completed.
The green LED flashes and stays on: both thresholds have
been teached, the sensor is ready to operate.
N.O./N.C. setup
1.) Press the button for 13 s. Both LED´s are
flashing alternately.
2.) Release the button: the green LED is on.
3.) During the green LED is on, the output is inverted by
pressing the button. If the button is not pressed during 10 s
the present output function is saved, the sensor is ready to
operate.
To return to factory setting (default)
1.) No object in sensing area.
Press the button 3 s until both LED´s are flashing
synchronously.
2.) No object in sensing area. Press the button 1 s.
The sensor is set to maximum sensitivity.
External Teach (ET)
+UB
- same function as button
-UB
- locked (disable teach button)
not connected
- operating mode
Warning
Use only power units with guarantee reliable
elect. isolation of the operating voltages as
per IEC 742 / EN 60742 / VDE 0551 with at
least 4 kV isolation resistance (PELV). Switch
power packs as per EN 60950 / VDE 0805 are
permitted.
Warning
Do not use as a safety device!
Electric voltage! Switch off voltage prior to
working on electrics.
détecteur à fibre optique
Raccordement des fibres optiques
1.) Couper la fibre à la longueur désirée.
2.) Ouvrir le serre-câbles
3.) Introduire la fibre optique aussi loin que possible
(surmonter la résistance du joint torrique).
4.) Fermer le serre-câbles.
Mode de travail: réglage du point de commutation
1.) Aligner la fibre sur l'objet. LED verte et LED jaune sont allumées
2.) Appuyer sur la touche pendant 3 s jusqu'à ce que les deux LEDs
clignotent simultanément (le premier seuil est saisi)
3.) Enlever l'objet de la zone de détection.
4.) Appuyer sur la touche pendant 1 s (l'arrière-plan est saisi) La
LED verte clignote, puis est allumée en permanence: le
deuxième seuil a été saisi. Le détecteur est operationnel.
Régler le point de commutation uniquement avec l'objet
1.) Aligner la fibre sur l'objet. LED jaune et LED verte sont
allumées.
2.) Appuyer sur la touche pendant 3 s jusqu'à ce que les deux
LEDs clignotent simultanément. (Le premier seuil est
saisi).
3.) Laisser l'objet dans la zone de détection, appuyer sur la
touche pendant 1 s. La LED verte clignote puis reste
allumée, le deuxième seuil a été saisi. Le détecteur est
operationnel.
Mode barrage photoélect.: réglage de la sensibilité (uniquement
nécessaire pour objets transparents
1.) Aligner l'émetteur sur le récepteur. Les deux LEDs sont
allumées.
2.) Appuyer sur la touche pendant 3 s jusqu'à ce que les deux
LEDs clignotent simultanément. (Le premier seuil est
saisi).
3.) Positionner l'objet dans la zone de détection.
4.) Appuyer sur la touche pendant 1 s
a:) La LED verte clignote puis reste allumée, le deuxième
seuil a été saisi. Le détecteur est operationnel.
b:) Les deux LEDs clignotent simultanément: le détecteur
ne détecte pas d'objet, aucun seuil n'a été saisi.
Règlage de sensibilité lorsqu'un procédé est en cours
1.) Aligner la fibre sur l'objet. LED verte est allumée, LED
jaune indéfinie.
2.) Uniquement le procédé en cours doit se situer dans le
chemin optique! Appuyer sur la touche 3 s jusqu'à ce que
les deux LEDs clignotent simultanément
3.) Appuyer à nouveau sur la touche pendant toute la durée
d'au moins 1 cycle de processus.
La LED verte clignote puis reste allumée: les deux seuils
ont été saisis, le détecteur est operationnel.
Réglage de sortie fermeture ou ouverture
1.) Appuyer sur la touche pendant 13 s. Les deux LEDs clignotent
à tour de rôle.
2.) Relâcher la touche: la LED verte est allumée.
3.) Pendant que la LED verte est allumée, la fonction de sortie
est invertie à chaque pression sur la touche.
Si la touche n'est pas activée pendant 10s, la fonction de
sortie actuelle est enregistrée. Le détecteur est
operationnel.
Etat d'origine/sensibilité maximale (par défaut)
1.) Aucun objet dans la zone de détection
Appuyer sur la touche pendant 3s jusqu'à ce que les deux
LEDs clignotent à tour de rôle
2.) Aucun objet dans la zone de détection. Appuyer sur la
touche pendant 1 s. Le détecteur est réglé
pour une sensibilité maximale.
Ligne pilote (ET)
+UB
- même fonction que la touche
-UB
- verrouillée (touche desactivée)
non raccordée
- mode de fonctionnement
Attention
N'utiliser que des blocs d'alimentation isolés
selon la norme IEC 742 / EN 60742 / VDE 0551
garantissant une tension d'isolement de 4 kV
min. (TBT). Les alimentations à découpage à
la norme EN 60950 / VDE 0805.
Attention
Ne convient pas pour une utilisation en tant
que dispositif de sécurité! Tension électrique!
Avant toute intervention sur le système élec-
trique: mettre hors tension.
Printed in Germany