Siemens SIMATIC NET S7-400 Instructions De Service page 114

Programmation des blocs client OPC UA
5.10 Codes d'erreur
Done Error ErrorID (hex) Nom
0 1 B0060010
0 1 B0070001
0 1 B0070002
0 1 B0070003
0 1 B0070004
0 1 B0070005
0 1 B0070006
0 1 B0070009
Codes d'erreur selon CEI 61131-3 pour OPC UA
0 1 002D0000
0 1 002E0000
0 1 002F0000
0 1 00300000
0 1 00960000
0 1 00A20000
0 1 00A30000
0 1 00A50000
0 1 00A60000
0 1 00A70000
0 1 00A80000
0 1 00A90000
0 1 00AA0000
0 1 00BA0000
0 1 406C0000
0 1 408F0000
0 1 40900000
0 1 40910000
0 1 40920000
0 1 40930000
0 1 40940000
114
GoodSubscription
Transferred
GoodCompletes
Asynchronously
GoodOverload
GoodClamped
GoodLocalOverride
GoodEntryInserted
GoodEntryReplaced
GoodNoData
GoodMoreData
GoodCommunicationEvent
GoodShutdownEvent
GoodCallAgain
GoodNonCriticalTimeout
GoodResultsMayBe
Incomplete
UncertainReferenceOutOf
Server
UncertainNoCommunication
LastUsableValue
UncertainLastUsableValue
UncertainSubstituteValue
UncertainInitialValue
UncertainSensorNotAccurate The value is at one of the sensor limits.
UncertainEngineeringUnits
Exceeded
Signification
Zone d'opérandes non valide dans une tâche de lecture ou
d'écriture : Les tableaux d'entrées, de sorties, de mémentos,
de données locales et de données locales du bloc antérieur
ne sont pas autorisés.
Paquet de données erroné dans UA_WriteList
La longueur de données à écrire excède le maximum.
Plage IndexRangeCount non valide
IndexRange Non valide. StartIndex ne doit pas dépasser
EndIndex et EndIndex ne doit pas être supérieur à la lon-
gueur de tableau.
AttributeID non valide
La zone de données est hors de la zone admissible.
Caractère non valide dans la chaîne.
The subscription was transferred to another session.
The processing will complete asynchronously.
Sampling has slowed down due to resource limitations.
The value written was accepted but was clamped.
The value has been overridden.
The data or event was successfully inserted into the historical
database.
The data or event field was successfully replaced in the his-
torical database.
No data exists for the requested time range or event filter.
The data or event field was successfully replaced in the his-
torical database.
The communication layer has raised an event.
The system is shutting down.
The operation is not finished and needs to be called again.
A non-critical timeout occurred.
The server should have followed a reference to a node in a
remote server but did not. The result set may be incomplete.
One of the references to follow in the relative path references
to a node in the address space in another server.
Communication to the data source has failed. The variable
value is the last value that had a good quality.
Whatever was updating this value has stopped doing so.
The value is an operational value that was manually overwrit-
ten.
The value is an initial value for a variable that normally re-
ceives its value from another variable.
The value is outside of the range of values defined for this
parameter.
Instructions de service, 01/2017, C79000-G8977-C427-02
CP 443-1 OPC UA