Worx WX530 Mode D'emploi page 13

Saw blade Assembly and Removing
Note: Lock or loose the blade
bolt, the spindle lock button
should be pressed.
WARNING: Always remove the
battery before changing the blade!
Hex key storage
OPERATION
Safety On/Off Switch
WARNING: To avoid cutting
injury from the sharp blade,
please don't put your hands around
the Base Plate.
NOTE: Keep the dust adapter
connected to dust collecting device
when using the tool.
Cutting Depth Adjusting
Cutting Guide
Bevel cuts
Note: Bevel cutting can't be used
under EXACTRACK TM
Sawdust Removal
EXACTRACK TM
What is EXACTRACK TM
EXACTRACK TM is an innovative function, which can help
to make a straight cut easier by keeping the blade flush
against the cutting guide board.
Safety notes
WARNING: Blade is sharp. Always wear
protective gloves.
Keep your hands off from the lower blade guard
after opening the lower blade guard.
TM
EXACTRACK operation scope
TM
1. EXACTRACK operates between 0~43mm in depth.
(See Fig. I)
TM
2. EXACTRACK works only with 90 degree cut, it does
not work with any angle of bevel cut.
Before operation
WARNING: Make sure battery is not installed
prior to making any adjustments to the saw,
and please place the battery pack nearby the saw.
1. Adjust the desired cutting depth (range 0~43mm).
(See Fig. I)
2. Turn the lever to EXACTRACK
3. Mark the desired cut line on the workpiece, then
clamp the cutting guide board (not supplied) to make
the board edge right on the cut line, the length of the
cutting guide board should leave 230mm longer at
the both ends. (See Fig. K1)
4. Place the EXACTRACK
on the top of cutting guide board (not supplied),
and ensure the main-base plate is sitting on the
workpiece. (See Fig. K2)
Cordless Circular Saw
See Fig. B
See Fig. C
See Fig. D
See Fig. E
See Fig. F
See Fig. G
mode.
See Fig. H
?
TM
mode. (See Fig. J)
TM sub-base plate (red part)
5. Open the lower blade guard manually (
your hands off the blade), push the saw against
the side of the cutting guide board, then release the
hand off the lower blade guard. (See Fig. K3)
Operation
1. Install the battery.
2. Please hold the saw firmly with both hands and
make sure the main base plate fits securely against
the cutting guide board (not supplied) during cutting.
(See Fig. K4)
3. Switch on the tool to start cutting (See Fig. K5)
STANDARD Mode
For regular 90 degree or bevel cutting (disable
TM
EXACTRACK fucntion), turn the lever to STANDARD
mode and then your tool can be used as a standard
circular saw. (See Fig. L)
The STANDARD mode can be used in the cutting depth
of 0~55mm (90 degree), 0~39mm (45 degree).
For product information, go to www.worx.com
and see How To video.
WORKING TIPS FOR YOUR
TOOL
If your power tool becomes too hot, please run your
circular saw no load for 2-3 minutes to cool the
motor. Avoid prolonged usage at very low speeds.
Protect saw blades against impact and shock. Do not
force the tool. Apply light and continuous pressure
in order to avoid overheating the blade tips. Cutting
with extreme force can significantly reduces the
performance capability of the tool and reduces the
service life of the saw blade. Sawing performance
and cutting quality depend essentially on the
condition and the tooth count of the saw blade.
Therefore, use only sharp saw blades that are suited
for the material being cut.
Choice of blades: 24 teeth for general work, approx.
40 teeth for finer cuts, more than 40 teeth for very
fine cuts into delicate surfaces, cement board, etc.
Only use saw blades recommended.
MAINTAIN TOOLS WITH
CARE
Remove the battery before carrying out any
adjustment, servicing or maintenance.
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Your power tool requires no
additional lubrication or maintenance. There are no
user serviceable parts in your power tool. Never use
keep
13
EN