Teka Maestro Infinity G1 Serie Mode D'emploi page 33

power off the zone, or you can choose a
different special function touching again
on the CHEF sensor
KEEP WARM FUNCTION
This function automatically sets an
appropriate power level to keep the
cooked food hot.
To activate it, select the plate, and
press on the CHEF sensor
until the led (16) located on the icon
lights up. Once the function is
activated, the symbol
on the power indicator (3).
You can override the function at
any time by turning off the plate,
by changing the power level or by
choosing a different special function.
MELTING FUNCTION
This function maintains a low
temperature in the cooking zone.
Ideal for defrosting food or for slowly
melting other food types as chocolate,
butter, etc.
To activate it, select the plate, and
press on the CHEF sensor
until the led (17) located on the icon
lights up. Once the function is
activated, the symbol
on the power indicator (3).
You can override the function at
any time by turning off the plate,
by changing the power level or by
choosing a different special function.
SIMMERING FUNCTION
This feature allows you to keep
simmered.
After the food is boiled, enable the
plate by selecting it, and press the
CHEF sensor (15) until the led
(18) located on the icon
up. Once the function is activated, the
symbol will appear on the power
indicator (3).
You can override the function at
any time by turning off the plate,
by changing the power level or by
choosing a different special function.
Flex Zone function
(15).
Through this function, it is possible to
enable two cooking zones work together,
and to select a power level and to activate
the timer function for both zones.
To activate this function, press the
sensor
decimal points (4) of the linked plates
will light up and the value "0" will be
(15)
shown on their power indicators (3).
The clock timer indicator (12) will show
three segments indicating the activated
will appear
zones. In case your model has several
zones with "Flex Zone", you can select
the desired option by pressing the
sensor
power to the chosen zone. You will
have a few seconds to perform the next
operation; otherwise, the function will
be disabled automatically.(see fig 8).
After the "Flex Zone" is selected, you can
assign the power by touching any of the
"sliders" cursors (2) of one of the linked
zone. The power level and its variations
are displayed simultaneously on the
power indicators (3) of both zones.
To disable this feature, you should
(15)
touch the sensor
when the function is disabled, the levels
of powers and functions assigned to the
will appear
related zones are cleared.
Safety switch off function
If due to an error one or several heating
zones do not switch off, the appliance
will be automatically discon-nected
after a set amount of time (see table 1).
Table 1
Selected
power level
0
1
lights
2
3
4
5
6
7
8
9
P
(14). By doing so, the
(14) before assigning the
(14) again. Also,
MAXIMUN
OPERATING TIME (in hours)
0
8
8
5
4
4
3
2
2
1
10 or 5 minutes, readjusts to
level 9 (depending on model)
When the "safety switch off" function
has been triggered, a 0is displayed if
the glass surface temperature is not
dangerous for the user or an H if there
is a burn risk.
Keep the control panel of the
heating areas clean and dry at all
times.
In the event of operating pro-
blems or incidents not mentioned
in this manual, disconnect the
appliance and contact the TEKA
technical service.
Suggestions and
recommendations
* Use pots or pans with thick, comple-
tely flat bottoms.
* Do not slide pots and pans over the
glass because they could scratch it.
* Although the glass can take knocks
from large pots and pans without
sharp edges, try not to knock it.
* To avoid damaging the ceramic
glass surface, do not drag pots
and pans over the glass and keep
the undersides of them clean and
in good condition.
* Recommended diameters of the pot
bottom (see ''Technical Data Sheet''
supplied with the product).
Try not to spill sugar or pro-
ducts containing sugar on the glass
as while the surface is hot these
could damage it.
Cleaning and maintenance
To keep the appliance in good
condition, clean it using suitable
products and implements once it has
cooled down. This will make the job
easier and avoid the build-up of dirt.
Never use harsh cleaning products or
tools that could scratch the surface, or
steam-operated equipment.
Light dirt not stuck to the surface can
be cleaned using a damp cloth and a
gentle detergent or warm soapy water.
However, for deeper stains or grease
use a special cleaner for ceramic hot
plates and follow the instructions on
EN
33