Safety Information - Cloer 5928 Manuel D'instructions

Description of appliance / parts:
1. Coffee pot with lid
2. 3-cup filter insert
3. 6-cup filter insert
4. Water tank with safety valve
5. Contact base with cord
Preparation for use
·
Remove all packaging elements and labels, but
not the rating plate.
·
Place the espresso maker on a dry, level, and
non-slip surface.
·
Make sure that the power cord never comes into
contact with hot surfaces.
·
Do not stretch the cord over corners and edges.
Before initial use
·
Clean the coffee pot, the filter insert, and the
water tank under clear, warm water to remove
any possible production residue.
·
Make sure not to immerse the contact base or
the water tank in water.
·
For hygienic reasons, we recommend that you
prepare and pour away a cup of espresso before
making your first real cup of espresso. You can
brew this trial espresso with the amount of
coffee required to make 3 cups.

Safety information

The appliance meets the
requirements of the applicable
Ec directives.
The appliance is intended
for in door use only.
·
Use the espresso maker only with the provided
contact base.
·
Do not place the contact base and the coffee
pot on a stove or gas flame.
·
The contact base may only be operated when
it is dry.
·
Please make sure that water is never spilled on
the contact base.
·
If water is accidentally spilled onto the contact
base, proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent dry
kitchen towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
cAuTIoN!
The espresso maker becomes
hot during operation. There is
a hazard of burn injury!
Avoid touching the surface of the
appliance. Grab the espresso
maker only by its insulated
handle!
·
Do not open the lid of the coffee pot during
operation. Scalding may result from escaping
steam!
·
Wait until the boiling process is complete and
the control lamp turns off.
Heruntergeladen von manualslib.de Handbücher-Suchmachiene
Do not remove the espresso
maker from the contact base
during brewing! Never try to
remove or re-adjust the coffee pot
and the water tank or perform
similar operations during the
operation of the espresso maker!
·
Unplug the power cord immediately if the
appliance, the rubber gasket or the electric cord
has become damaged.
·
Unplug the appliance after using it.
·
Use only espresso coffee powder.
cAuTIoN!
Fill the water tank only with
water and never with milk, sugar
or other liquids or ingredients!
·
Do not overfill the espresso maker. If the
espresso maker is overfilled, boilling coffee may
be ejected.
ATTENTIoN!
Always unplug appliance when
not in use and before cleaning!
operation
Making 6 cups of espresso:
·
Fill the water tank with water up to the "6"
mark.
·
Take the 6 cup filter insert (including the coil)
and fill it to the brim with ground espresso
powder.
·
Smoothen the espresso powder across the
brim, but do not press the powder deeper into
the filter.
·
Insert the filled filter insert into the water tank.
·
Remove any leftover powder from the brim to
allow for a perfect seal along the gasket.
·
Screw the top of the espresso maker to the
water tank.
·
Place the top of the espresso maker straight
onto the water tank and tighten it by turning it
clockwise.
·
The arrows on the top of the espresso maker and
water tank must be at least above each other or
if possible tighten a little further.
·
Make sure the tanks do not tilt and the pot
is closed tightly to prevent any steam from
escaping.
·
You can now place the espresso pot onto the
contact base.
·
Insert the plug into the wall socket.
·
Switch the espresso maker on.
·
Do not open the lid during operation. Danger
of scalding!
·
The espresso is finished as soon as the control
lamp goes out.
·
Unplug appliance from the wall socket.
·
You can now serve the espresso.
cAuTIoN!
The housing of the espresso
maker is hot! Grab the pot only
by its handle!
·
Before making more espresso, let the appliance
EN
9