Atlas Copco A4350001 Serie Mode D'emploi page 3

ITB-A31-10-10
Technical Data
Product Data
Motor voltage
Motor power
Speed
Torque range
Weight
Battery Compatibility
Accessory
Battery, 14V (2.5Ah)
Battery, 18V (2.5Ah)
Battery, 36V (2.5Ah)
EU SAR value
EU SAR Value: 0.55
Wireless LAN Information
Regulatory Do- Band
main
ETSI 2.4 GHz
U-NII-1
U-NII-2
U-NII-2e
FCC/IC 2.4 GHz
U-NII-1
U-NII-2
U-NII-2e
U-NII-3
Charger Compatibility
Accessory
Flex charger
Maximum Radio Output Power
Frequency Range
Radio Technology (MHz)
Wi-Fi® 2402-2480
Wi-Fi® 5180-5320
Wi-Fi® 5500-5700
35 V d.c.
1080 W
1270 r/min
3 - 12 Nm (2.2 - 8.8 ft lb)
1.5 kg (3.3 lb)
Article nr.
4211 6130 02
4211 6030 85
4211 6030 86
TxChannels
1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11
36, 40, 44, 48
52, 56, 60, 64
100, 104, 108, 112,
116, 120, 124, 128,
132, 136, 140
1, 2, 3, 4, 5, 6, 7, 8,
9, 10, 11
36, 40, 44, 48
52, 56, 60, 64
100, 104, 108, 112,
116, 132, 136, 140
149, 153, 157, 161,
165
Article nr.
4211 6083 84
Maximum Trans-
mit Power EIRP
(dBm)
19.46
20.37
18.39
© Atlas Copco Industrial Technique AB - 9834 5880 00
Frequency Range
Radio Technology (MHz)
Bluetooth® wire- 2402-2480
less technology /
Bluetooth® Low
Energy
Wi-Fi® is a registered trademark of Wi-Fi Alliance®
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG,Inc.
Ambient Temperature
Operating temperature, charge
Operating temperature, discharge
Storage temperature
Charger Temperatures
Charger operating tempera-
ture
Product Power Source
This product can be used with either a battery, or with an
electrical power cable in combination with a power supply
unit.
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rotational
direction after any event that can influence the tightening re-
sult. Examples of such events include but are not limited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures or
practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair of
the equipment.
Safety Information
Maximum Trans-
mit Power EIRP
(dBm)
9.29
+5 to +40 °C
(+41 to +104 °F)
0 to +40 °C
(+32 to +104 °F)
−20 to +40 °C
(−4 to +104 °F)
+5 to +40 °C
(+41 to +104 °F)
3