R&G CP0312 Notice De Montage page 5

Off side (right side as you sit on bike)
Remove the engine/frame bolt in position arrowed in picture 'G' (using 14mm socket), you will

have to remove the fairing panel bolt (fairing bolt arrowed) to allow fitment of the crash protector
mounting block.

Slide one of the 10mm washers onto one of the M10 hexagon headed bolts (150mm long) so
washer sits against head of bolt as shown in picture 'H'.
Page | 5

Next slide one of the smaller spacers (5mm wide) over the bolt so it sits against the washer just
fitted as shown in picture 'H'.

Next slide one of the serrated locking washers over the bolt so it sits against spacer just fitted as
shown in picture 'H'.

Next slide the bolt with washers through either crash protector so head of bolt goes into counter-
bore in crash protector as shown in picture 'H.

Place one of the longer spacers over the exposed end of the bolt so it sits against the crash
protector as shown in picture 'H' (please note the slightly larger diameter sits against the crash
protector.
Offer the crash protector assembly up to the engine/frame mounting hole as shown in picture 'I'.


Finally tighten the crash protector bolt until you feel some compression from inside the protector
using 17mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST BE
POSITIONED AS IN PICTURE 'C' WITH BIGGER END TOWARD FRONT OF BIKE.
Turn a little more so that you feel the compression increase slightly. Then apply a quarter turn.
Do not over tighten as damage can occur to the bike. Do not exceed 40Nm of torque. Please
ensure the crash protector does not come into contact with the fairing panel as you tighten the bolt.

If not already fitted fit bubble sticker into recess of crash protector cap.

Fit crash protector cap into crash protector.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Issue 1 22/03/2012 (NSY)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
ISSUE 1
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
03/02/2012 (NSY)
R&G Racing
www.rg-racing.com Email: info@rg-racing.com