Manuels Connexes pour Nilfisk Advance AquaPro C
Sommaire des Matières pour Nilfisk Advance AquaPro C
- Page 1 AquaPro ™ Instructions for use and parts list Advance MODEL 56102800 06/03 revised 11/03 Form Number 56041561...
-
Page 2: Parts And Service
INTRODUCTION This manual will help you get the most from your Advance AquaPro C. Read thoroughly before operating the machine. NOTE: Bold numbers in parenthesis indicate an item illustrated on page 7. This product is intended for commercial use only. PARTS AND SERVICE Repairs, when required, should be performed by your authorized Advance Service Center, who employs factory-trained service personnel, and maintains an inventory of Advance original... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices other than normal residential housekeeping purposes. When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using this appliance. -
Page 4: Consignes De Securite Importantes
CONSIGNES DE SECURITE IMPORTANTES Cette machine ne convient qu´à un usage industriel, par exemple dans des hôtels, écoles, hôpitaux, usines, boutiques et bureaux et autres à l´exclusion de tout usage de maintenance résidentielle normale. L’utilisation d’un appareil électrique demande certaines précautions LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL) AVERTISSEMENT! Pour réduire les risques d’incendie, de choc électrique ou de blessure:... -
Page 5: 120Vac Grounding Instructions
120VAC GROUNDING INSTRUCTIONS This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. -
Page 6: Instructions Visant La Mise À La Terre (120Vac)
INSTRUCTIONS VISANT LA MISE À LA TERRE (120VAC) Cet appareil doit être mis à la terre. En cas de défaillance ou de panne éventuelles, la mise a la terre fournit au courant un chemin de moindre résistance qui réduit le risque de choc électrique. Cet appareil est pourvu d’un cordon muni d’un conducteur de terre et d’une fiche avec broche de terre. -
Page 7: Know Your Machine
KNOW YOUR MACHINE KNOW YOUR MACHINE DESCRIPTIONS Operator Handle (1) - Operator holds this to move the machine from one location to another. Lift Handle (2) - Operator grasps this handle when lifting the machine. Solution Tank Lid (3) - Fill Solution Tank here with warm water and chemicals. Recovery Tank Lid (4) - The Recovery Tank can be flushed out by running clean water into this opening with the Recovery Tank Drain Hose open. -
Page 8: Wiring Diagram
SWITCH PLATE DESCRIPTIONS Vacuum Switches (1 and 2) - These switches each turn one vacuum on and off. The switches will light when ON. When using just one vacuum, as when cleaning delicate fabric, use vacuum 1. Pump Switch (3) - This switch turns the pump on and off. The switch will light when ON. ➁... - Page 9 OPERATION Inspect the machine, hoses, and cleaning tool(s) for cleanliness and completeness. Fill the Solution Tank with warm water. Using warm water may be a benefit in cleaning ° ° effectiveness, but do not use hot water (above 140 F / 60 C) in the tank.
-
Page 10: Use And Maintenance
USE AND MAINTENANCE Use only liquid chemicals with a pH between 6 and 9 at the recommended mix ratios. Improper chemicals, or improperly mixed chemcials, can cause possible damage to the pump, seals, and other components. Turn the pump “off” when the solution tank is low on fluid. Do not let the pump run dry. Regularly clean any mineral or chemical deposits in the heat exchanger, lines and pump with a mild acid descaler.