Publicité
FITTING INSTRUCTIONS
REMOVE SEAT USING KEY.
DISCONNECT THE TAIL LIGHT ELECTRICAL CONNECTOR AS ARROWED IN
PICTURE 1.
FROM BELOW, REMOVE THE FOUR BOLTS ARROWED IN PICTURE 2 USING A
10mm SOCKET AND A WRENCH. GENTLY WITHDRAW THE OEM LICENCE PLATE
BRACKET AND THE WIRING.
ON THE OEM LICENCE PLATE BRACKET, REMOVE THE 6 SCREWS ARROWED IN
PICTURE 3 USING A T15 TORX KEY.
GENTLY SPLIT THE OEM LICENCE PLATE BRACKET IN A HALF. PLEASE NOTE
THE ORIENTATION OF THE CONNECTORS AS THEY NEED TO BE RECONNECTED
AT LATER STAGE. DISCONNECT ALL ELECTRICAL CONNECTORS (INDICATORS
AND LICENCE PLATE ILLUMINATOR) FROM THE SUB-HARNESS.
REMOVE THE INDICATOR NUTS AS ARROWED IN PICTURE 4 USING A 13MM
SPANNER. REMOVE THE INDICATORS AND ITS WIRING FROM THE OEM
LICENCE PLATE BRACKET. PLEASE NOTE THE ORIENTATION LOCATION OF THE
INDICATORS.
REMOVE THE SUB-HARNESS COMPLETELY FROM THE OEM LICENCE PLATE
BRACKET AS SHOWN IN PICTURE 5.
FROM THE KIT, TAKE THE R&G LICENCE PLATE BRACKET (ITEM 8) AND
ATTACH R&G LICENCE PLATE ILLUMINATOR (ITEM 9) THROUGH THE 3 IN-LINE
HOLES AS ARROWED IN PICTURE 6. SECURE THE LICENCE PLATE
ILLUMINATOR USING THE WASHERS AND NUTS PROVIDED IN THE KIT.
FIT LICENCE PLATE SHROUD (ITEM 10) USING A SMALL AMOUNT OF SUPER-
GLUE OVER THE LICENCE PLATE ILLUMINATOR (ITEM 9) (SHOWN IN PICTURE
7).
FROM THE KIT, TAKE THE M6 x 20mm BOLTS (ITEM 11), M6 WASHERS (ITEM 2)
AND 5mm SPACERS (ITEM 6). INSERT THEM INTO THE TWO MOUNTING HOLES
LOCATED AT THE BACK OF LICENCE PLATE BRACKET (ITEM7) AS SHOWN IN
PICTURE 8.
OFFER THE ASSEMBLY TOWARDS THE ORIGINAL MOUNTING POINTS ON THE
OEM TAIL UNIT AND WIND IN THE TWO BOLTS A COUPLE OF TURNS. DO NOT
FULLY TIGHTEN THE TWO BOLTS (ITEM 11) AT THIS STAGE AS 8mm SPACERS
AND SUPPORT BRACKETS NEED TO BE INSERTED ONTO THE OTHER TWO
MOUNTING HOLES LOCATED ON THE FRONT OF LICENCE PLATE BRACKET
(ITEM 8). FEED ALL THE WIRING (INDICATORS AND LICENCE PLATE
ILLUMINATOR WIRES) THROUGH THE ORIGINAL HOLE ON THE OEM TAIL UNIT.
FROM THE KIT, TAKE THE L/H SUPPORT BRACKET (ITEM 3) AND INSERT THE
RUBBER GROMMET (ITEM 5) INTO THE ROUND HOLE PROVIDED AS SHOWN IN
PICTURE 9. REPEAT THE PROCEDURE FOR R/H SUPPORT BRACKET (ITEM 4).
FROM THE KIT, TAKE THE M6x25mm BOLTS (ITEM 12), 4 x M6 WASHERS (ITEM 2),
2 x 8mm SPACERS (ITEM 7) AND THE TWO SUPPORT BRACKETS JUST
ASSEMBLED EARLIER (ITEM 3 AND 4 WITH THE RUBBER GROMMETS). POSITION
THE PARTS AROUND THE REMAINING TWO MONTING HOLES LOCATED ON THE
FRONT OF LICENCE PLATE BRACKET (ITEM 8) AS SHOWN IN PICTURE 10.
GENTLY TIGHTEN THE ASSEMBLY UP AND ADJUST THE POSITION OF BOTH
SUPPORT BRACKETS (ITEM 3 AND 4), ENSURE THAT THE RUBBER GROMMETS
ARE SITTING NICELY PUSHING AGAINST THE OEM REAR BODY PANEL.
TIGHTEN ALL BOLTS ONCE POSITIONED TO 15Nm. PICTURE 12.
Page | 5
Publicité
