THOMSON ROC Z907 Mode D'emploi page 6

7.2.1 Fixed code/ Rolling code procedure (with
manual registration for synchronisation with the
door system)
For some door operator manufacturers, it is additionally
necessary to register/synchronise the handheld transmit-
ter with the receiver of the door operator system.
• Please consult the operating instructions for the door
operator (there is generally a section on registering a
new handheld transmitter).
• Make sure that you are close to the door operator
receiver (about 50 cm).
• Usually a set button is activated on the door operator
system to register handheld transmitters, and a LED
lights up (can vary according to manufacturer).
• Normally, you now have about 20–30 seconds to
register/synchronise the ROCZ907.
• Synchronisation generally takes place when you press
the programmed/copied button of the ROCZ907 three
times in succession.
7.2.2 Rolling code procedure (with automatic reg-
istration for synchronisation with the door system)
Due to the rolling code principle, it is often necessary to
register/synchronise the handheld transmitter with the
receiver of the door operator system.
• Please consult the operating instructions for the door
operator (there is generally a section on registering a
new handheld transmitter).
• Make sure that you are close to the door operator
receiver (about 50 cm).
• Usually it is sufficient to press and hold the pro-
grammed button of the ROCZ907 until the red function
LED (1) flashes quickly (about 10 seconds).
• Now release the button. The remote control goes into
synchronisation mode with the door operator system. The
latter confirms the synchronisation after about 5–10 sec-
onds by means of an illuminated or flashing LED. Once
synchronisation has ended, the fast flashing red LED on
the ROCZ907 goes out; registration was successful.
7.3 Copy function – complex rolling code
Some door operator manufacturers require transmission
of the source code (often also called SEED code) to be
able to teach in the ROCZ907 onto the door operator.
Here, it is essential to have the original functioning hand-
held transmitter (master function) with the source code!
4
Depending on manufacturer, the procedure of the
original remote control for transmitting the source code
(master remote control) is now implemented.
Details of the procedure can be found in the original operat-
ing instructions for the handheld transmitter or door operator.
7.3.1 Example for BFT (manufacturer):
• Before performing the copy function, make sure that
the original handheld transmitter and the ROCZ907
are facing each other and not more than 3 cm apart.
• Make sure that you are close to the door operator
receiver (about 50 cm).
• Press and hold the '1' button on the ROCZ907 and
keep it held while pressing the '2' button four times.
Release both buttons. The red function LED (1) now
flashes about every 2 seconds.
• On the original handheld transmitter, press and hold
the button you are copying until the red function LED
of the ROCZ907 lights up and successively flashes
twice about every 2 seconds.
• Now press the button concealed on the back (battery
compartment) (old BFT models) or buttons 1 and 2
(newer models) on the original handheld transmitter
(master). The red LED on the ROCZ907 flashes quickly
in succession. Now press and hold the button you
wish to program (for example, '1') until the red LED of
the ROCZ907 goes out.
• Press and hold the programmed button of the ROCZ907
until the red LED flashes quickly (about 10 seconds).
Release the button. Programming has been completed
when the red LED on the ROCZ907 goes out.
• Then check whether the door can be controlled using
the button that has been taught to; if not, repeat the
procedure.
7.3.2 Example for FAAC, Genius, Amigo, Kilo
(manufacturers):
• Before performing the copy function, make sure that
the original handheld transmitter and the ROCZ907
are facing each other and not more than 3 cm apart.
• Make sure that you are close to the door operator
receiver (about 50 cm).
• Press and hold the '1' button on the ROCZ907 and
keep it held while pressing the '2' button four times.
Release both buttons. The red function LED (1) now
flashes about every 2 seconds.