Publicité
Safety and Regulatory Information
Declaration of Conformity
Declaration of Conformity
Declaration of Conformity
______________________________________________________________
Manufacturer's Name:
Manufacturer's Address:
declares, that the product
Product Name:
N2724NAZ product family including associated Cxxxxyy and Axxxxyy models
Model Numbers:
Product Options:
conforms to the following Product Specifications:
Safety:
EN 60950:1997 +A1 +A2 +A3 +A4 +A11 / IEC 60950:1991 +A1 +A2 +A3 +A4
EN 60825-1:1994 +A11:1996 / IEC 60825-1:1993 Laser Class 1
EMC:
EN 55022:1998(3rd) / CISPR 22 (1997, 3. Ed.) A1+A2, Class B
EN 50082-1:1997(2nd Ed.)
EN 55024-2:1998 / IEC 1000-4-2 (1995), 4 kV CD, 8 kV AD
EN 55024-3:1998 / IEC 1000-4-3 (1995), 3 V/m
EN 55024-4:1998 / IEC 801-4-4 (1988), 1 kV Peak Power Lines
EN 61000-3-2 1995 1.Ed / IEC 1000-3-2 (1995), Harmonics
EN 61000-3-3:1995 / IEC 1000-3-3 (1994), Flicker
Supplementary Information:
The product herewith complies with the requirements of the following Directives and carries the CE marking accordingly:
the EMC Directive 89/336/EEC -the Low Voltage Directive 73/23/EEC (including 93/68EEC).
The Manufacturer listed above declares that this product has been tested and found to comply with the limits of a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures: a) Reorient or relocate the receiving antenna, b) Increase the separation between the
equipment and receiver, c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected, or
d) Consult the dealer or an experienced radio/TV technician for help.
Change or modification of this equipment not expressly approved by Hewlett-Packard could void the user's authority to operate this
equipment. Only use the cables, connectors, power cords, and accessories supplied with this equipment or expressly approved by
Hewlett-Packard.
For Regulatory Compliance Information ONLY, contact:
Australian: Product Regulations Manager, Hewlett-Packard, Australia Ltd., 31-41 Joseph Street, Blackburn, Victoria
3130, Australia
European: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department TRE,
Herrenberger Strasse 130, D-71304 Boblingen (FAX:+49-7031-14 3143)
USA:
Product Regulations Manager, Hewlett-Packard Company, 700 71st Avenue, Greeley, CO 80634 USA,
(Phone: 970-350-5600).
D-2
according to ISO/IEC Guide 22 and EN 45014
Hewlett-Packard Co.
Hewlett-Packard Data Protection-Greeley
700 71st Avenue
Greeley, CO. 80634 USA
HP Surestore Tape Autoloader 1/9
Where x is any numeric character and y is any alpha character
All Options
0,5 kV Signal Lines
October, 2000 Greeley, Colorado, USA
_________________________________
J. Steven Becker, Quality Eng. Manager
Appendix D
Publicité
