Equipment Compliance; Periodic Inspection And Repair - Tractel blocfor 1.8 EVO ESD-EN 360 Manuel D'installation, D'emploi Et D'entretien

12. Equipment compliance

TRACTEL SAS RD 619 – Saint-Hilaire-sous-Romilly
GB
– F-10102 Romilly-sur-Seine France hereby declares
that the safety equipment described in this manual,
• complies with the requirements of Regulation (EU)
2016/425 of the European Parliament of March 2016.
• is identical to the PPE, having been subject to the
"CE"-type-examination certificate issued by the
APAVE SUDEUROPE SAS – CS 60193 – 13322
Marseille – France, identified under the number 0082,
and tested according to the 2002 EN 360 standard.
• is subject to the procedure referred to in Annex
VIII of Regulation (EU) 2016/425 of the European
Parliament, module D, under the control of a notified
body: APAVE SUDEUROPE SAS – CS 60193 – 13322
Marseille – France, identified under the number 0082.
Name of product:
B X ESD Y-Z
B: for the name blocfor™
X: the type of blocfor™ within the range (B1.8A EVO,
B1.8B EVO)
ESD: generic term for the range
Y: Connector model: device
Z: Connector model: retractable lanyard
Example:
B1.8A EVO ESD M10-M47
blocfor™ self-retracting fall-arrester from the ESD
range, type 1.8A EVO ESD, fitted with a model M10
connector on the device and a model M47 connector on
the retractable lanyard.
The label on each blocfor™ self-retracting fall-arrester
indicates:
a. The trade name: TRACTEL
b: The name of the product,
c: The reference standard followed by the year of
application,
d: The product reference,
e. CE Logo followed by the number 0082, identification
number of the approved body responsible for
production control,
f. Year and month of manufacture,
g. The serial number,
8
13. Marking
,
®
h. A pictogram showing that the manual must be read
before use,
w. Maximum operating load,

14. Periodic inspection and repair

An annual periodical inspection is required, but
depending on the frequency of use, environmental
conditions and regulations of the company or the
country of use, periodical inspections may be more
frequent.
Periodical inspections shall be carried out by an
approved and competent technician and in accordance
with the manufacturer's examination procedures as laid
down in the file "Verification procedures for TRACTEL
PPE".
Verification of the legibility of the marking on the product
is an integral part of the periodical inspection.
Following the periodical inspection, a certificate of
return to service must issued by the approved and
competent technician who performed the periodical
inspection. This return to service must be recorded on
the inspection sheet in the middle of this manual. This
inspection sheet should be retained throughout the life
of the product until it is scrapped.
After arresting a fall, this product must undergo a
periodical inspection, as described in these instructions.
Any textile components of the product must be replaced,
even if they do not display any visible alteration.
15. Lifespan
TRACTEL textile PPE equipment, such as harnesses,
®
lanyards, ropes and energy absorbers, TRACTEL
Mechanical PPE equipments as stopcable™ and
stopfor™ fall-arresters, blocfor™ self-retracting fall-
arresters, and the TRACTEL
without restrictions from their manufacturing date
providing that:
– A normal use is made in accordance with the
instructions manual,
– A periodical inspection,
accomplished at least once a year by an approved
and competent technician. At the end of this
periodical inspection, the PPE must be certified fit
to return to service, in writing,
– Instructions manual procedures for storage and
transport are strictly met.
– As a general rule and so long as the conditions of
use mentioned above are respected, their life cycle
may be longer than 10 years.
®
®
lifelines can be used
®
which must be