Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
More ice fisherman choose Eskimo than any other brand
Quickflip
2 (69167), Quickflip
™
ASSEmBly INSTRuCTIONS
Tools needed - two 7/16" wrenches and a Phillips screwdriver.
ASSEMBLY NOTE: This ice shelter should be assembled in a
garage or basement setting due to the time and length of assem-
bly. Identify and familiarize yourself with all parts and hardware
before assembly. Allow 1-3 hours for assembly.
ASSEMBLY NOTE: The use of a cordless drill with socket will
make assembly of your ice shelter much quicker. Be sure to set
the drill speed low so you do not over tighten any nut and bolt
combinations.
ASSEMBLY NOTE: If a Tracking kit is purchased with the shel-
ter, it should be mounted to the sled before assembly of the ice
shelter for convenience.
ImPORTANT ASSEmBly TIP: DO NOT fully TIGHTEN ANy NuT
AND BOlT COmBINATIONS uNTIl All BOlT-ON PARTS ARE
ASSEmBlED TOGETHER! fINGER TIGHTEN ONly! THIS WIll
HElP HOlE AlIGNmENT Of All PARTS.
fOR QuICKflIP 2 & ExPRESS 2
1. Attach sled support bar (69677) and the left hinge assembly (69309L) to
the upper lip of sled using (4) provided 1/4-20 x 7/8" bolts, nyloc nuts and
washers. SEE fIGuRE 1A.
NOTE: Be sure hinge assembly is orientated as shown in fIGurE
1A, with high sides of hinges placed to the front of sled and hinge
poles to the inside.
2. Attach sled support bar and the right hinge assembly (69309R) to the upper
lip of sled using (4) provided1/4-20 x 7/8" bolts, nyloc nuts and washers.
NOTE: Be sure hinge assembly is orientated with high sides of
hinges placed to the front of sled and hinge poles to the inside.
fOR QuICKflIP 3
1. Attach the left hinge assembly (68426) to the upper lip of sled using (3)
provided 1/4-20 x 7/8" bolts, nyloc nuts and SAE washers. SEE fIGuRE
1B.
NOTE: Be sure hinge assembly is orientated as shown in fIGurE
1B, with high sides of hinges placed to the front of sled and hinge
poles to the inside.
2. Attach the right hinge assembly (68425) to the upper lip of sled using (3)
provided 1/4-20 x 7/8" bolts, nyloc nuts and SAE washers.
NOTE: Be sure hinge assembly is orientated with high sides of
hinges placed to the front of sled and hinge poles to the inside.
ASSEMBlY NOTE: The J-leg pole assemblies for each hinge
assembly have been removed from the hinge assembly for pack-
aging reasons. You must re-attach the J-leg pole assemblies to
each hinge assembly using the provided 1/4-20 x 1-1/4" phillips
truss head bolts, nyloc nuts and pole hinge caps. Be sure J-legs
are positioned correctly on hinge (inside of hinges). SEE pArTS
ExplOSION ON pAGE 12.
1-800-345-6007
3 (69168) & Express
™
™
GetEskimo.com
2 (69802)
left hinge bracket
fIGuRE 1A (left side shown)
left hinge
bracket
fIGuRE 1B (left side shown)
®
high side of bracket
(4) 1/4" x 7/8" bolts
sled support bar
(4) 1/4" washers
(4) 1/4" nuts
(3) 1/4" x 7/8" bolts
high side of bracket
(3) SAE washers
(3) 1/4" nuts
Page 5
Publicité
Table des Matières
