Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Always wear SAFETY GLASSES
when installing hitch
①
End panels
②
M10 Factory
bolts
Access
holes
③
④
Fasteners
typical
both sides
Figure 1
Conical washer
teeth side
against hitch
1.
Lower Exhaust: Using exhaust removal pliers, remove (2) rubber hangers from both sides of exhaust.
2.
Remove Fascia: a) Using 10 mm socket and flat head screwdriver, remove (1) screw and (2) rivets from wheel well, both sides.
b) Using plastic trim tool, remove wheel well trim, both sides.
c) Using flat head screwdriver, remove (1) rivet from under wheel well trim, both sides.
d) Using 10 mm socket remove (1) screw from bottom corner of fascia, both sides.
e) Open trunk to access taillights. Using plastic trim tool, remove cover panels from taillight. Using 10mm socket, remove lowest fastener from under taillight cover. Using Phillips
screwdriver, remove two visible fasteners from lower trunk opening.
f) Using flat head screwdriver, remove (2) rivets from bottom of fascia, both sides.
g) Using plastic trim tool, unclip fascia from vehicle. Disconnect wiring if equipped. Remove fascia by pulling rearward and set aside in safe place.
3.
Remove bumper beam: Using 14mm socket, remove (6) M10 factory bolts attaching bumper beam to vehicle. Return bumper beam to vehicle owner, save for reinstall.
4.
Install hitch: a) Remove plug from access hole shown in Figure 1. Using die grinder, enlarge hole to fit 1/2" carriage bolt ① and spacer ② through hole, both sides of vehicle.
b) Using 11/16" Socket, detach brackets from hitch before installation. Save 7/16" carriage bolts, 7/16 conical washer, and 7/16 nut for reinstall. Apply blue thread locker to all bolts.
Using the reverse pull wire method ⑤, attach the 1/2" carriage bolt ① and spacer ② to pull wire and pull fasteners into position, both sides, see Figure 4. Loosely install
bracket to vehicle frame rail using 1/2" conical washer ③, and nut ④, both sides.
c) Raise hitch into position and loosely install (6) M10 factory bolts, (3) per side. Reinstall 7/16" carriage bolts, 7/16" conical washers and 7/16" nuts removed in step 4b, both sides.
5.
Tighten 7/16" fasteners with torque wrench to 50 Ft.-Lb. (68 N*M)
6.
Tighten M10 factory bolts with torque wrench to 42 Ft.-Lb. (57 N*M)
7.
Tighten 1/2" fasteners with torque wrench to 75 Ft.-Lb. (102 N*M)
8.
Trim Fascia: Trim fascia in area shown in Figure 2. Note: DO NOT cut wires if equipped. For models with kick sensor see Figure 3 for trim modification.
9.
Reinstall fascia, wiring, and exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
© 2022 Horizon Global™ Corp. - Printed in Mexico
Installation Instructions
PART NUMBERS: 76929
Area to trim
Frame rails
4.25"
11.00"
Figure 2
Reverse pull wire method
⑤
Figure 4
A. Insert bolt and
B. Align block on
access hole
Block into frame
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 4 of 27
Fastener Kit: 76929F
Carriage bolt
① Qty. (2)
1/2"-13 x 2.00, GR5
Spacer
② Qty. (2)
.250 x 1" x 3"
Conical washer
③ Qty. (2)
1/2"
Qty. (2) Hex nut
④
1/2" -13 GR2
Pull wire
⑤ Qty. (2)
1/2"
Warning Card
⑥ Qty. (1)
Warning Label
⑦ Qty. (2)
Bolt
⑧ Qty. (2)
M12x1.75x100 mm, CL10.9
Flat Washer
⑨ Qty. (2)
7/16"
Prevailing Torque Nut
⑩ Qty. (2)
M12x1.75, CL10
Cable Ties
⑪ Qty. (4)
C. Pull bolt
thru block
76929NP
09-13-22
Rev. A
Publicité
Table des Matières
