Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
For ADA compliance installation guidelines, please type the model number into our website .
RECOMMENDED TOOLS AND ACCESSORIES
• Measuring tape
• Phillips screwdriver no . 2
• Flat blade screwdriver (to open knockout holes)
• Saw (to cut holes in cabinet)
• Sheet metal shears)
• Pliers
• Metal foil duct tape
CONTENTS
Before proceeding to the installation, check the contents of the box . If items are missing or damaged, contact the
manufacturer .
Make sure that the following items are included:
PM300SS
(1) G
REASE
C
B
ABINET
(
ATTACHED TO THE BACK OF THE UNIT
(1) P
B
ARTS
AG
(4) N
. 8-18
1/4"
O
X
M
S
ETAL
CREWS
(8) N
. 8-15
5/8"
O
X
RD. HD.
W
S
OOD
CREWS
* F
IND PARTS BAG BEHIND THE WIRING COMPARTMENT COVER
HR0280A
INSTALL THE DUCTWORK
(DUCTED INSTALLATION ONLY)
NOTE: To reduce the risk of fire, use only metal ductwork .
1 . Decide where the ductwork will run between the hood and
the outside . (FIG . 1)
2 . A straight, short duct run will allow the unit to perform most
efficiently .
3 . Long duct runs, elbows, and transitions will reduce the
performance of the unit . Use as few of them as possible .
Larger ducting may be required for best performance with
longer duct runs .
4 . Install wall cap or roof cap (sold separately) . Connect metal
ductwork to cap and work back towards the unit location .
Use 2" metal foil duct tape to seal the joints between
ductwork sections .
F
ILTER
RACKETS
)
* C
:
ONTAINING
(4) N
. 8-32
1/4"
O
X
M
S
ETAL
CREWS
(4) N
. 6-18
3/4"
O
X
T
H
RUSS
EAD
W
S
OOD
CREWS
.
• Scissors (to cut metal foil duct tape)
• Pencil
• Wire stripper
• Strain relief, 7/8" diameter (to secure house wiring
cable to the hood)
• BP87Q Damper (optional)
BBN1243SS, BBN1303SS
(2) G
F
(
REASE
ILTERS
ATTACHED TO THE BACK OF THE UNIT
(1) S
ET OF
(1) P
B
ARTS
AG
(4) N
. 8-18
1/4"
O
X
M
S
ETAL
CREWS
(8) N
. 8-15
5/8"
O
X
RD. HD.
W
S
OOD
CREWS
* F
IND PARTS BAG BEHIND THE WIRING COMPARTMENT COVER
HR0281A
R
OOF CAP
7"
ROUND DAMPER
BP87Q (
)
OPTIONAL
U
NIT
24"
- 30"
MIN
ABOVE COOKING SURFACE
HH0315A
C
B
ABINET
RACKETS
)
3 F
ILLERS
* C
:
ONTAINING
(4) N
. 8-32
1/4"
O
X
M
S
ETAL
CREWS
(4) N
. 6-18
3/4"
O
X
T
H
RUSS
EAD
W
S
OOD
CREWS
.
7"
ROUND DUCT
W
ALL CAP
7"
ROUND ELBOW
H
OUSE WIRING
MAX
FIG. 1
5
10-0547
Publicité
Table des Matières
