R&G CP0294 Guide Rapide page 5

Off side (right side as you sit on bike)

Remove fairing panel.

Remove water bottle (no need to remove pipes - just undo bolts and pull forward to allow access to the engine
bolts).

Remove both of the top engine bolts as shown in picture 'E'.

Using R&G aluminium block and the two M10 socket-headed cap bolts supplied, insert the bolts into the
Page | 5
aluminium block. Use the longer bolt for the top hole.

Take the two M10 rubber washers and fit 1 over each bolt up to block.

Assemble block to bike and tighten bolts.

Refit the water bottle.

Place right-hand side template over fairing using top two screws to locate. Hold in place with masking tape (on
outside of panel)

Mark on fairing where rough position of hole will be.

Drill pilot hole.

Carefully, using a Dremel tool or similar, cut the hole but do not go right to lines.

Offer fairing back up to bike and open hole up until it goes over the aluminium block.

When this is achieved, refit fairing.

Take one of the 12mm hex-headed bolt and place plain washer over bolt up to head of bolt then place locking
washer over bolt up to plain washer just fitted. Place bolt assembly through protector and place the shaped spacer
over exposed end of bolt, then take the M12 rubber washer and place over bolt and push up to shaped spacer just
fitted.

Offer this assembly through the hole in fairing (ensuring the assembly does not distort the fairing) up to mounting
block and tighten bolt until you feel some compression from inside the protector using 19mm socket and wrench.
PLEASE NOTE THE CRASH PROTECTOR MUST BE POSITIONED AS IN PICTURE 'C' WITH
BIGGER END TOWARD FRONT OF BIKE. Turn a little more so that you feel the compression increase
slightly. Then apply a quarter turn. Do not over tighten as damage can occur to the bike. Do not exceed 40nm of
torque.

Fit protector cap.
IMPORTANT NOTE:
W
E WOULD ADVISE WHEN CUTTING PANELS TO WEAR A FACEMASK
FIBRE CAN BE DANGEROUS TO HEALTH
Due to the risk of cross threading of bolts etc.; we always recommend that our products be fitted by one of our official
Dealers or a qualified mechanic.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
(
USED ON
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
ISSUE 1
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
,
IN A WELL
RSVR ).
PANEL
03/10/2011 (NSY)
R&G Racing
www.rg-racing.com Email:
- . C
VENTILATED AREA ARBON
info@rg-racing.com