Preparation For Operation - GRAPHITE 59G717 Manuel D'instruction

Spindle guard
4.
Base
5.
Plate
6.
Depth gauge stepped bumper
7.
Anti-dust shield of the body guide
8.
Depth gauge locking knob
9.
Depth gauge
10.
Depth gauge indicator
11.
Main scale
12.
Precision scale
13.
Knob for precise depth adjustment
14.
Plunge guide locking lever
15.
Indicator for precise depth adjustment
16.
Illumination
17.
Spindle spring
18.
Collet sleeve
19.
Fixing nut
20.
Locking knobs for edge guide bars
21.
Grooves for edge guide bars
22.
Switch
23.
Switch lock button
24.
Wheel for rotational speed control
25.
Edge guide bar
26.
Edge guide
27.
Knob for edge guide position adjustment
28.
Indicator of edge guide position
29.
Adapter fixing screw
30.
Dust extraction adapter
31.
Reducing connector
32.
Spike
33.
Butterfly nut of the spike
34.
Guide sleeve
35.
Guide sleeve collar
36.
Flat key
37.
* Differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Edge guide
1.
Spike for cutting along arcs
2.
Guide sleeve
3.
Dust extraction adapter with reducer
4.
Adapter fixing screws
5.
Collet sleeve
6.
Flat key
7.

PREPARATION FOR OPERATION

Spindle lock button can be used only for working tool installation
or removal. It cannot be used as a brake button when the spindle
is rotating. Otherwise the power tool may be damaged or the user
may be injured.
Do not tighten the spindle nut strongly before inserting a working
tool, this can damage the collet sleeve. Make sure that appropriate
collet sleeve is used each time the working tool is replaced.
Choice of working tool depends on processed material and type of
planned task. Cutter bits made of high speed steel (HSS) are designed
for processing soft materials, like plastics or soft wood. Cutter bits
made of sintered carbide (HM) are designed for processing harder
materials, e.g. hard woods, chipboards, or even aluminium if allowed
by the cutter bit manufacturer.
Use only working tools whose allowable rotary speed is higher or
equal to maximum power tool speed with no load.
INSTALLATION OF WORK TOOLS
Disconnect the power tool from power supply.
Use protective gloves for installation and removal of working
tools.
• Lower the spindle guard (4).
• Press and hold the spindle lock button (2). If necessary, turn the
spindle (3) by hand until the lock engages. Depending on the
working tool shaft diameter, use appropriate collect sleeve (19).
Bear in mind the spring (18) that operates with it. When replacing
the collet sleeve, start with putting the spring (18) into the
spindle, then collet sleeve (19) of appropriate size. Then lock them
in place by installing the fixing nut (20).
• Slide the working tool shank into the spindle to at least 20 mm
depth.
• Tighten the fixing nut (20) with the flat key (37) (fig. C).
• Release the spindle lock button (2).
• Set up the spindle guard (4).
Tighten the fixing nut with the flat key only when there is a
working tool inside the spindle. Otherwise handle the fixing nut
gently and only by hand, to avoid damage to the collet sleeve.
INSTALLATION OF DUST EXTRACTION ADAPTER
You can protect yourself from dust by using anti-dust mask and
appropriate device for dust extraction.
Disconnect the power tool from power supply.
Remove working tool before installing dust extraction adapter
(31) (fig. B).
• Loosen the plunge guide locking lever (15) to set the router
spindle in upper position.
• Place the dust extraction adapter (31) in the base (5) and fix with
adapter fixing screws (30) (fig. B), by driving them from below.
• Connect dust extraction hose to the dust extraction adapter (31)
either directly or use reducing connector (32), depending on the
connector diameter of the hose.
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the router
- 1 pce
rating plate.
- 1 pce
The router is equipped with the switch lock button that protects
- 1 pce
against accidental start up.
- 1 set
Switching on
- 1 set
• Press the switch lock button (24).
- 3 pcs
• Press and hold the switch (23).
- 1 pce
Switching off
• Release pressure on the switch button (23).
Illumination
The device is equipped with illumination feature (17) that improves
visibility in the workplace. Illumination turns on automatically when
the device is turned on.
13
OPERATION / SETTINGS