Assembly - IKRA GESI 1000 Manuel D'utilisation

from power supply. Check condition of
cutting head - look for cracks.
49. Be sure to bring the unit onto normal work-
ing position before turning it on again.
50. Have a damaged cutting head replaced
immediately - even if it only has super-
ficial cracks. Never attempt to repair a
damaged cutting head.
51. Always switch off your tool and discon-
nect it from the power supply before
taking a break and after finishing work.
Do not forget maintenance. (Plug dis-
connected!) Only carry out maintenance
and repairs described in these operating
instructions. Any other work should be
performed by your dealer. Do not grease -
this is unnecessary, as this unit has been
pregreased at the factory.
52. Inspect cooling air slots on the motor
housing at regular intervals for clog-ups
and clean as necessary.
53. Only use original spare parts.
54. Clean plastic parts with a damp cloth. Do
not use aggressive cleaning chemicals.
55. Never hose down the electric tool!
56. Cleaning and maintenance may not be
carried out by children.
57. Store tool indoors in a dry, high or locked
place and always keep out of reach of
children.
Important notice - so your guarantee does not expire:
• Always keep the air-intake clean.
• Never press the cutting head on the ground, when
doing this you brake the turned-on motor.
• Never hit the cutting head on a hard under-ground,
otherwise you will unbalance and damage the motor
shaft.

6. Assembly

WARNING: Do not touch the gear head immedi-
ately when the product using in a long time, the hot
gear head may scald you.
Shoulder strap (Fig. 2)
A shoulder strap (20) is supplied for your greater comfort.
Simply attach the clip of the shoulder strap onto the strap
onto the hanger at the front of housing body (4).
Connecting the attachment to the upper shaft (Fig. 3)
1. The coupler (17) connects the attachment to the up-
per shaft. Follow these steps to connect the attach-
ment to the upper shaft.
2. Loosen the wing nut (9) by turning it counter clock-
wise.
3. Remove the end cap from the shaft (7).
GB | Operating Instructions
4. Align the button with the guide recess on the upper
5. Slide the underneath shaft (10) into the upper tube (7)
Note: If the button does not release completely in the
positioning hole, upper shaft (10) are not locked. Slightly
rotate the underneath shaft until the button is locked
into place.
6. Tighten the wing nut (9) securely by turning it clock-
Note: During operation, periodically check the wing nut
(9) and tighten as necessary.
Removing the attachment from the upper shaft (Fig. 3)
Disconnect the upper shaft and underneath shaft for
storage or when a job calls for a different attachment.
Follow these steps to remove the attachment from the
upper shaft.
1. Release the switch (5) and allow the trimmer to coast
2. Unplug the brush cutter.
3. Loosen the wing nut (9) by turning it counterclock-
4. Push the button, while pulling out the attachment.
Attaching the front handle (Fig. 4)
Follow these steps to attach the front handle:
1. Press the front handle (19) onto the upper shaft.
2. Place the front handle along the upper shaft to a posi-
3. Slide the bolt (37) through the hole in the barrier
4. Slide the bolt (38) through the Quick Open Button
Adjusting front handle (Fig. 5)
1. Loosen the Quick Open Button (18) by turning it as
2. Adjust the sencond handle.
3. Locking the Quick Open Button (18) by turning it as
Note: During operation, periodically check the Quick
Open Button (18) and tighten as necessary.
Attaching the guard (Fig. 6 + 7)
Follow these steps to attach the guard:
1. Attach the guard (14) to the gear head (15).
2. Install three screws (29) from the underside of guard
Attachment the safety guard (Fig. 6 + 7)
Follow these steps to attach the brush cutter guard:
1. Attach the blade guard (11) to the mounting bracket
2. Install two screws (47) from the top of the mount-
3. Attach the trimmer guard (12) to the blade guard (11).
GB-8
shaft.
until the underneath shaft clicks into place.
wise.
to a stop.
wise.
tion that allows for comfortable operation.
handle (8) and front handle.
(18) and the hole in bolt (37) and tighten it securely.
Fig.5 shown.
Fig.5 shown.
(14) through the gear head (15).
(30).
ing bracket through the blade guard and into the
threaded mounting plates (24).