Bort MASTER ECO Mode D'emploi page 6

CLEAN THE WASH FAN WRAPPING PLACE FROM THE
SEALANT OR THE GARBAGE.
NOTE: It may be necessary to expand the drain hole
for installation flange fastening disposer. Equip-
ment for extending the drainage hole is purchased
separately.
3. DISASSEMBLY OF THE ASSEMBLY UNIT
Turn over the assembly (Fig.4.1) and loosen the
three fixing screws (1) The access to the ring (2).
Disconnect the retaining ring from the flange with
a screwdriver. Now the assembly unit can be disas-
sembled.
4. ATTACHING THE FIXING ASSEMBLY TO
WASHING Fig.5.1.
1. Install one or two rubber gaskets (2) under the
washing flange (1). Make sure that The drainage
hole is not clogged, and set to flange washer / gas-
ket. In order to The flange of the sink became in
place, you need to crush it with a heavy load. (To
avoid scratches, use a towel as a lining.)
2. Put the second rubber part on the bottom of the
kitchen sink a gasket (2), a cardboard gasket (op-
tional) (3) and a metal support ring (4) (flat side up).
3. While holding the second rubber gasket, card-
board padding (optional) and a metal support ring,
put the mounting ring (5) on the flange of the sink
so that it aligned with the support ring.
4. Pressing tightly to the bottom of the sink rubber
gasket, cardboard gasket, support ring and mount-
ing ring, slide the snap ring (7) onto the flange of
the sink so that it snaps into the flange groove.
5. Tighten the three fixing screws (6) to The fixing
assembly was tight and evenly pressed to the sink.
5. CLEANING THE DRAIN PIPE
If you do not clean the drain pipe, it can clog.
1. Remove the water trap. (Fig.6.1)
2. Using a cleaner, remove all solid precipitation in
the horizontal part of the drainage pipes, moving
with side of the siphon towards the main pipe.
IF THE DISHWASHER WILL NOT BE CONNECTED TO
THE DISPOSER, GO TO PART 7 OF THIS INSTRUCTION
6. CONNECTING THE DISHWASHER MACHINES
AND TRANSFER CONNECTION
If the sink is full of liquid it can be discharged into
the disposer through the inlet in its upper parts.
(Fig. 7.2)
On all models inside the intake pipe there is parti-
tion. The partition must be removed (Fig. 7.1).
REMOVING THE PLATE / PARTITION
1. Place the disposer on one side and place it screw-
driver into the connection for the dishwasher, push-
ing it until it will not rest against the partition in the
end of the branch pipe.
2. With several blows of the hammer, knock out the
septum in the branch pipe (Fig. 7.1).
3. Remove the embossed partition from the dis-
poser bowl. If necessary to connect the dishwasher,
then it should be connected to the inlet of the over-
flow outlet pipes To connect to the overflow inlet,
remove the exhaust pipe cover by unscrewing the
cover (Fig. 7.3).
7. CONNECTING THE DISPOSER TO THE FIXING
UNIT ATTENTION!
To avoid injury, follow the so that during the remov-
al and installation of a part Your body was not under
the disposer; during the installation it is possible to
drop it.
Remove any objects from the grinding chamber
product before installing it on the sink.
1. Install the product in such a way that provide
easy access to the restart button engine located in
the lower part of the body. Do not block this place
with any objects.
2. Place the disposer with three mounting loops
(1) into the sliding position by mounting rails (2).
(Fig. 8.1)
3. Lift the disposer, insert the top end (installation
gasket) in the mounting and turn the setting ring to
the right (with a wrench or adjustable pliers) until
the mounting loops are fixed (3) with respect to the
mounting rails (Fig. 8.2).
Make sure that all three mounting loops are locked.
Disposer is installed.
4. Run water into the sink, then check the connec-
tions for leaks.
5. Insert the noise absorbing screen into the drain
hole flat side up. (Fig.8.3)
8. CONNECTING THE OUTLET PIPE
• To the DRAIN PIPE ATTENTION!
• It is recommended to wear protective goggles
when installing the disposer.
• For all models, the drain pipe is connected using
a screw connection (Fig. 9.2). First connect the hy-
draulic lock to the disposer and then to the drain.
For the connection a siphon with smooth walls
should be used.
• Use a sanitary sealant only for connecting the
flange of the sink with the disposer.
• Do not use sealants for threaded pipe connec-
tions or anaerobic screwed sealants. They can
damage the product.
• Regularly check the disposer and fittings for wa-
ter leaks, since leaks water can cause damage to
property.
10
• The manufacturer is not responsible for damage
to property as a result of water leaks.
INSTALLING THE DRAINAGE SYSTEM
1. Put the flange (2) on the drain pipe Insert the rub-
ber seal (1). Fasten drain tube, tightly pulling it to
the body disposer with screws (4). (Fig. 9.1)
9. CONNECTING THE DISPOSER TO THE ELECTRI-
CAL NETWORK
ATTENTION! ELECTRIC SHOCK CURRENT
To prevent electric shock, turn off the power before
installing or servicing the product.
If you are not qualified enough, call an electrician to
connect the product to the power.
If a three–pin grounding–type plug is used to con-
nect a three–contact outlet with ground.
Do not modify the design of the plug supplied with
the device.
Improper equipment grounding may cause electric
shock current.
All electrical connections must comply with the
electrical and norms.
Do not connect the ground to the feed pipe gas.
Do not power on the distribution shield until you
have installed the sockets with proper grounding.
If the power cord is damaged, it must be replaced at
the service center.
NOTE: Access to a grounded outlet is required. In-
stalling all additional outlets must be carried out by
a qualified electrician, and all outlets must be prop-
erly grounded.
Turn ON/OFF device
Depending on the models BORT disposer are
equipped with two types of control: a wireless (wall)
switch or a pneumatic switch.
Wireless (wall) switch
The disposer of the "Control and FullControl" series
are equipped with a wireless wall mount switch.
The switch should be located in a convenient (safe
for children) place above the table top.
For instal the switch to the wall, use double–sided
tape.
For activate / deactivate the device, hold down the
key for 2–3 seconds.
Battery type: Voltage: 12V; Size: A27
Air switch
Disposer is equipped with an air switch and a con-
necting pipe (except "Control" series).
INSTALLATION OF AIR SWITCH
1. Drill a hole with a diameter of 32 mm in suitable
top or top the panel of a sink. Some sinks may al-
ready have a suitable A hole for the opening of
which is necessary remove the cover.
2. Unscrew the nut from the body of the push but-
ton, while holding the stainless steel washer and
rubber gasket in place. Place one end of the PVC
tube on the spout on the body Press the other end
to A hole in the table top and a nut located under
the countertop. (Fig. 10.2)
3. Place the push button housing in the hole and
tighten the nut underneath countertop (enough
arm effort). Do not use the key to tighten nut. (Fig.
10.3)
4. Take the other end of the duct and tightly put it
on the spout of the air switch located on the bot-
tom of the disposer. (Fig.10.4) Hand tighten the
clamping nut. The disposer installation is complete.
Before using the product, read all of the instruc-
tions. operation and safety contained in paragraph
10 of this manual. In conclusion, install the plug in
the sink in the Closed position. Fill the sink with wa-
ter, Remove the plug and check the connections on
the a water leakage.
10. ATTENTION! IMPORTANT INSTRUCTIONS FOR
SAFETY
• If the air switch does not work, remove the plug
power supply from the outlet and check the air
duct pneumatic switch and delivered to the out-
let electricity.
• This product is designed for grinding food resi-
dues at home; the ingress of substances other
than food into the disposer may cause injury and
/ or damage property. To reduce the risk of Do not
use a washer with an installed disposer not for
food purposes (for example, for bathing a child or
washing your head).
• Children should be supervised adults and should
not play with a disposer. To reduce the risk of in-
jury It is necessary to keep a watchful eye on chil-
dren use of the product.
• If the wedging in the disposer is eliminated, turn
off the appliance and disconnect it from the elec-
trical network. Use a wrench for self–removal of
jammed waste according to description in the
section "Elimination of jamming disposer ".
• Use tongs or pliers to remove foreign objects from
the product.
• To reduce the risk of injury from particles that
are thrown out by the disposer, it is prohibited to
use grinders withoutnoise shielding screen (Fig.
8.3). Place the plug in the drain hole, as shown in
Fig. 11.2 or 11.4.
• Do not allow the following items to fall into the
disposer: shells, including oyster, caustic means
for cleaning pipes or similar chemical products,
glass, porcelain or plastic, large (hollow) bones,
metal objects (bottle caps, cans, or kitchen appli-
ances), hot fat or other hot liquids.
11