R&G LP0238BK Instructions page 7


Refit the OEM indicators to the licence plate bracket (part 1) using the slots on the side in the same way as the
OEM part and refit the plastic locking key.

Use the 4 self-adhesive cable clips (item 8) in the locations shown in picture 17.

Neatly route the wiring using the cable clips as shown in picture 18.

Using the 4 OEM bolts removed earlier, mount the licence plate bracket as shown in picture 19.

Fit the rubber gasket (item 2) into the wiring hole as shown in picture 19 and thread the wiring through the
Page | 7
gasket as shown in picture 20.

Connect the OEM indicator wiring in the same way it was removed:

Test the indicators and licence plate illuminator for correct function and flash rate.

If indicators fail to illuminate swap the connectors.
If fitting R&G mini indicators-Not included (Product codes: RG370=Bulb, RG371=LED, RG372=Aero LED)

Pass one length of heatshrink (item 7) over the wiring on both mini indicators as shown in picture 15.

Take 2 mini indicator adaptors (item 3) and place them either side of the indicator mount on the licence plate
bracket part 1 (item 1) ensuring that the locators secure into the slot on the licence plate bracket as shown in
picture 16.

Pass the R&G mini indicator through the holes in the indicator adaptors and use the flange nut supplied with the
indicator to hold it in place as shown in picture 16.

Ensure the indicator wiring passes through the hole into the licence plate bracket.

Repeat this process for both indicators.

Use the 4 self-adhesive cable clips (item 8) in the locations shown in picture 17.

Neatly route the wiring using the cable clips as shown in picture 18.

Using the 4 OEM bolts removed earlier, mount the licence plate bracket as shown in picture 19.

Fit the rubber gasket (item 2) into the wiring hole as shown in picture 19 and thread the wiring through the
gasket as shown in picture 20.

If only fitting mini indicators to the rear of the motorcycle and leaving the OEM indicators on the front connect
the indicator wiring to a resistor (R&G product code: RGR0001) and connect this to the motorcycle loom
following this scheme:
LHS Indicator (marked on motorcycle loom with purple insulation tape):
RHS Indicator (marked on motorcycle wiring with green insulation tape)

Test the indicators and licence plate illuminator for correct function and flash rate.

If indicators fail to illuminate swap the connectors.

If fitting R&G mini indicators to the front of the motorcycle replace the rear resistor (RGR0001) with
(RGR0002) and use resistor (RGR0001) for the front indicators.

Refit the seat panel, rider seat and pillion seat in the same way they were removed.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
LHS Indicator (marked on motorcycle loom with purple insulation tape):
Motorcycle loom BLACK-----------OEM indicator PURPLE
Motorcycle loom BLACK/WHITE-OEM indicator BLACK/WHITE
RHS Indicator (marked on motorcycle wiring with green insulation tape)
Motorcycle loom BLACK-----------OEM indicator GREEN
Motorcycle loom BLACK/WHITE-OEM indicator BLACK/WHITE
Motorcycle loom BLACKResistor (RGR0001) YELLOWR&G mini indicator YELLOW
Motorcycle loom BLACK/WHITEResistor (RGR0001) BLACKR&G mini indicator BLACK
Motorcycle loom BLACKResistor (RGR0001) YELLOWR&G mini indicator YELLOW
Motorcycle loom BLACK/WHITEResistor (RGR0001) BLACKR&G mini indicator BLACK
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
ISSUE 2 16/01/2018 (HB)
R&G
www.rg-racing.com Email: info@rg-racing.com