Miscellaneous Settings; Other Options; Video/Hdmi Setup - Rotel RSX-1562 Manuel De L'utilisateur

English

Miscellaneous Settings

Other Options

O T H E R
R E C O R D : S o u r c e
T U R N O N
M A X
P O W E R : D i r e c t
L A N G U A G E : E N G L I S H
D I S C R E T E : N o
S / W U P G R A D E : E n t e r
M A I N M E N U
This OTHER OPTIONS menu, accessed from the MAIN menu, provides
access to several miscellaneous settings as follows:
RECORD: Select which source signal to be sent to the recording outputs
by choosing one of the input sources. The options are: CD, TUNER, VIDEO
1–6, USB, and SOURCE. You can either select a specific component
or select SOURCE which will send the signal to the record outputs from
whatever source is selected for listening. The default is SOURCE.
TURN ON VOL: Specifies a default volume level to be used each time
the unit is activated. You can select LAST to have the unit power up with
the last previously used volume setting. Or, you specify a volume from
MIN (full mute) to MAX, in 1dB increments. Note that this setting cannot
exceed the MAX VOL established in the next line of the menu.
MAX VOL: Specifies the maximum volume level for the unit. The volume
cannot be adjusted above this level. Settings range from MIN to MAX,
in 1dB increments.
POWER: This setting determines how the unit powers up. With the
default STANDBY setting, the unit powers up in standby mode when
AC is applied and the rear panel POWER button is ON. The unit must
be activated using the front panel STANDBY button or the remote ON/
OFF buttons.
With the DIRECT setting, the unit is fully activated when AC power is
applied and the rear panel POWER button is ON; however, it may be
put in standby mode using the front panel STANDBY button or the remote
ON/OFF buttons.
In ALWAYS-ON mode, the unit remains fully active whenever AC is present
and the rear panel POWER button is ON; the front panel STANDBY button
and the remote ON/OFF buttons are disabled and the unit cannot be
put in standby mode.
In RESUME mode, the unit will return to the last power condition setting
when switched on. For example, when the AC mains power is switched
OFF during operation, it will return to operating mode when the mains
power is switched on again.
LANGUAGE: Selects a language for the On Screen Display
DISCRETE: The default setting of NO allows control of input selection
in remote ZONE 2–4 from the main room remote control. Changing the
setting to YES prevents the remote control in the main room from affecting
any remote monitors in any way.
O P T I O N S
V O L : L a s t
V O L : M a x
Note: The DISCRETE function is intended for use by a Rotel dealer or
installer only.
Rotel's use of discrete IR commands in multi-zone models provides easier
integration with IR control systems, making control possible from a single
IR input. For Rotel dealers or installers, further information is available on
the Rotel website: www.rotel.com
Go to 'Support' for downloads and technical updates, or search for
'discrete' to find relevant items. Remote commands are available in Philips
Pronto CCF format and in RTI CML format at:
www.rotel.com/downloads/prontocodes.htm
www.rotel.com/downloads/rticodes.htm
S/W UPGRADE : Enter this menu if you wish to upgrade the unit's
firmware.
Note: The S/W UPGRADE function is intended for use by a Rotel dealer
or installer only.
Change settings on the OTHER OPTIONS menu by highlighting the desired
line using the Up/Down buttons and using the Left/Right buttons to step
through the available settings. To return to the MAIN menu, press the
ENT button. Press the RCVR/SETUP button on the remote to cancel the
display and return to normal operation.

Video/HDMI SETUP

V I D E O / H D M I
A N A L O G V I D E O O U T
H D M I A U D I O M O D E : A M P
H D M I C O N T R O L : O n
P O W E R C O N T R O L : N o
M A I N M E N U
The VIDEO/HDMI menu deals with the configuration of the HDMI output
for high-definition video display devices. See the Video Inputs & Outputs
section of this manual.
ANALOG VIDEO OUT: Specifies the video resolution and format of the
analog video output at the TV MONITOR outputs. The receiver will scale
all analog video inputs up to this specified resolution for a perfect match
with the native resolution of your HDTV monitor . Can be 480p/576p,
720p, 1080i, 1080p.
HDMI AUDIO MODE: options are AMP MODE and TV MODE. In
AMP MODE the HDMI Audio and other audio (analog or digital) inputs
are processed and sent by the RSX-1562 for output to the connected
amplifier(s). TV MODE (pass-through) provides HDMI Audio and other
audio (analog or digital) outputs for use with an audio-capable display
device. In TV MODE, there is no audio output from the RSX-1562.
HDMI CONTROL: Options are On, Off. Set to On to enable the ARC
(Audio Return Channel) feature. For ARC to function, your display (TV,
monitor) must be ARC capable and must be connected the RSX-1562's
HDMI OUT 1(labeled ARC). ARC allows the RSX-1562 to receive the
audio signal from the TV 's tuner through the HDMI OUTPUT 1 of RSX-
: 4 8 0 p / 5 7 6 p
M o d e
45