Important Safety Information - Oster OBL234X Mode D'emploi

IMPORTANT SAFETY INFORMATION

Read all instructions before using this product.
1. This appliance shall not be used by children. Children shall not play with the
appliance. Keep the appliance and its cord out of reach of children.
2. Appliances can be used by persons with reduced physical, sensory, or mental
capabilities or lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and understand the
hazards involved.
3. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or has been damaged in any manner. If the supply cord is damaged,
it must be replaced by the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
4. To protect against electric shock, do not place or immerse cord, plugs, or motor
base in water or other liquid. The jug, blade, seal, and locking ring should be washed
in warm, soapy water. Please refer to Page 6 for cleaning instructions.
5. The blades have very sharp edges, take care when handling or cleaning.
6. Always disconnect from the power supply if left unattended and before assembling,
disassembling or cleaning. To disconnect turn any control to off then unplug from
the power supply. Do not unplug by pulling on the cord.
7. Never use this appliance for anything other than its intended use. Misuse can cause
injuries. This appliance is for household use only. Do not use this appliance outdoors.
8. Never attempt to overcome the interlock.
9. The blender and its accessories should not be used for longer than 2 minutes
continuously.
10. Be careful if hot liquid is poured into the blender as it can be ejected out of the
appliance due to a sudden steaming;
11. CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-
out, this appliance must not be supplied through an external switching device, such as
a timer, or connected to a circuit that is regularly switched on and off by the utility;
This appliance must not be placed on or near any potentially hot surfaces (such as a gas or electric hob).
Never let the power cord hang over the edge of a work top, touch hot surfaces or become knotted, trapped or pinched.
Do not use the appliance if it has been dropped, if there are any visible signs of damage or if it is leaking.
Make sure that all attachments are securely and correctly fitted before operating the appliance.
Allow moving parts to come to a stop and unplug the appliance before changing or cleaning accessories.
Avoid contact with moving parts. Keep hands and utensils out of the jug while blending to prevent personal injury or damage to the
blender. A rubber spatula may be used only when the blender is not running and the appliance is unplugged.
Do not use the blender without the lid and feeder cap in place.
Never attempt to place the blade assembly onto the motor unit without the jug.
Never attempt to fit or remove the jug to the motor unit when the motor is running.
Do not blend carbonated liquids, this may create an overpressure hazard.
4
OBL234X_20MLM1 (EMEA).indd 4-5 OBL234X_20MLM1 (EMEA).indd 4-5
This appliance is for household use only. Do not use the appliance for anything other than intended use. Do not use this appliance
outdoors.
Never use any attachment or accessory not recommended by the manufacturer.
Always ensure that hands are dry before handling the plug or switching on the appliance.
Always use the appliance on a stable, secure, dry and level surface.
1. Jug Lid Cap/Measurer
2. Jug Lid
3. 1.25 Liters (5 Cups) Heat-Resistant Boroclass ® Glass Jug
4. Sealing Ring
5. Special 6-Point Blade with Jug Bottom
6. Motor Base with integrated Jug Collar
7. Control Panel
ASSEMBLY
1. Turn the jar upside down so the small opening is at the top.
2. Turn the Special 6-Point Blade with Jug Bottom upside down and
place into the bottom of the jug.
3. Position the open end of the jug bottom over the jug. Turn clockwise to
tighten. Be sure the jug bottom is locked securely to the jug before using.
4. Slide the jug onto the base.
5. Plug the power cord into a standard household outlet of the same
voltage as the one indicated in the rating plate of your blender. You are now ready to start.
USING THE PRE-PROGRAMMED SETTINGS
Select Smoothie or Food Processor Function, by pushing the correct button.
1. Press the power button to turn the product on. The power light will illuminate,
meaning the product is active and ready to use.
2. Put the ingredients into the jug.
3. Secure the lid and the jug lid cap.
4. Press one of the two Pre-Programmed Setting buttons appropriate for your recipe.
The button will illuminate.
Press Start / Stop button to begin.
PARTS
CONTROL PANEL
a. Pre-Programmed Settings
- Smoothie Button
- Food Processor Button
b. Manual Speeds 1, 2 & 3
c. Pulse button
d. Reverse Pulse button
e. Power Button
f. Start/Stop Button
5
2/20/20 10:08 2/20/20 10:08