Complete Assembly; Grass Cutting; Controls Description - GGP ITALY MCS 504 PRO Handle Serie Manuel D'utilisation

OPERATING INSTRUCTIONS
For information on the engine and the battery (if sup-
plied), read the relevant owner manuals.
NOTE – The number which precedes each paragraph
links the references in the text to the respective illus-
trations (listed on page iii and following pages).

1. COMPLETE ASSEMBLY

NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING! Unpacking and completing the assem-
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1 Assembling the handle
Attach the top of the handle (1) to the bottom (2) using the
knob (3) and the washer (4).
Secure the control cables using the binders (8).
Loosen the lower screws (9) to adjust the height of the
handle .
By loosening the knob (3), the top part of the handle (1) can
be turned laterally making mowing near walls easier.
The screws (9) and the knob (3) must always be tightened
thoroughly while mowing.
• Manual ignition models
• Electric key ignition models
Fit the starter cable (5) in the guide (6) and tighten the
nut (7).
1.2 Battery connection
• Electric key ignition models
C onnect the battery cable to the general wiring connec-
tor on the lawnmower.
• Electric push-button ignition models
F ollow all the instructions provided in the engine
Instruction Manual.

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for
a throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
2.3 Drive lever (where applicable)
On power-driven models, pull the lever (1) toward the op-
All manuals and user guides at all-guides.com
erator for forward movement.
Drive can be engaged only when the engine is running.
The lawnmower stops moving forward when the lever (1) is
in the "N" position.
Releasing the cutting means brake lever, the lever (1)
moves automatically to the "N" position, stopping all for-
ward movement.
The cutting height is adjusted by the specific lever (1).
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.
During ignition, follow the instructions in the engine manual
• Manual ignition models
P ull the cutting means brake lever (1) against the handle
• Electric key ignition models
P ull the cutting means brake lever (1) against the handle
• Electric push-button ignition models
I nsert the consent key (4) firmly in its seat, then pull the
The appearance of the lawn will improve if you alternate
cutting in both directions at the same height.
A machine that is equipped with a MULCHING system cuts
the grass, chops it then distributes it over the lawn. It is not
necessary to collect the cut grass.
For best MULCHING results, proceed as follows:
1. N ever cut the grass too short. Only cut the grass by 1/3
2. K eep the body shell perfectly clean (underneath).
3. A lways use well sharpened cutting means.
4. A void mowing wet grass. It accumulates more easily
Lawn care recommendations
Each type of grass has different characteristics and may
thus require different ways of caring for the lawn; always
read the instructions on seed boxes for mowing height for
the growing conditions in the work area.
Keep in mind that most grass is made up of a stem and one
or more leaves. If leaves are fully cut, the lawn is damaged
and growth is more difficult.
The following indications generally apply:
– c utting too low tears and uproots the grass, giving it a
– i n the summer, cutting must be higher to prevent the
– d o not cut wet grass; this could reduce cutting means ef-
– f or particularly high grass, initially mow at the maximum
When work has been completed, release the brake lever (1)
4
2.4 Cutting height adjustment

3. GRASS CUTTING

3.1 Engine ignition
and firmly tug the knob on the ignition cable (2).
and turn the ignition key (3).
cutting means brake lever (1) against the handle, press
the ignition button (5) and hold until the engine is running.
3.2 Mowing the lawn
of its height.
under the body shell and the mowing performance de-
creases considerably.
"spotted" appearance;
ground from drying;
ficiency due to sticky grass and tear the lawn.
height allowed by the machine then mow again after two
or three days.
3.3 When work is finished