Yamaha M2500 Séries Mode D'emploi page 38

(MIDI channel) ....................................... 1–16
Select the MIDI channel that will be used when MIDI
data is transmitted/received via the MIDI IN/OUT
connectors.
(program change transmission/reception) ...
This specifies whether or not program change mes-
sages will be transmitted/received via the MIDI IN/
OUT connectors.
• If " " is selected
Program changes will not be transmitted or received.
• If " " is selected
Program changes will be transmitted and received.
– When program changes 0–127 are received at the
MIDI IN connector, scene memory numbers 1–128
will be recalled. (However if the utility item "Recall
operation" is set to "
will be ignored.)
– When you recall a scene memory number 1–128 in
which a scene has been stored, a program change
0–127 will be transmitted from the MIDI OUT
connector. (Even if the Utility item "Recall Opera-
tion" is set to " ," you can use the 0–9/ENTER
and RECALL switches to transmit program
changes 0–7 from the MIDI OUT connector.)
• If " " is selected
Program changes will be transmitted and received.
– Program changes will be received in the same way
as for the " " setting.
– Even when you recall a scene memory number 1–
128 in which no scene has been stored, a program
change 0–127 will be transmitted from the MIDI
OUT connector.
(control change transmission/reception)......
Specify whether control change messages will be
transmitted/received via the MIDI IN/OUT connec-
tors.
• If " " is selected
Control change messages will not be transmitted or
received.
• If " " is selected
Control change messages will be transmitted and
received.
– When control change numbers 1–70 are received,
the corresponding channel will be switched on/off.
When mute groups are used, control change num-
bers 105–112 will switch mute groups 1–8 on/off.
(For details refer to the following section "Control
change table.")
(factory setting: " ")
....oFF/on/LoC
(factory setting: " ")
," program changes 0–7
.... oFF/GrP/on
(factory setting: " ")
• If " " is selected
Only the control change numbers (105–112) that
correspond to mute groups 1–8 will be transmitted
and received.
(program change reception omni on/off).....
Specify whether or not the MIDI channel specified by
the Utility item CH will be used when receiving pro-
gram change messages.
• If " " is selected
Program change messages will be received on all
MIDI channels (1–16).
• If " " is selected
Program change messages will be received only on
the MIDI channel specified by the Utility item CH.
(echo back) ..........................................on/oFF
Specify whether messages received at the MIDI IN
connector will be echoed back from the MIDI OUT
connector. If this is turned "
echoed back. However if a bulk dump request is
received, that message itself will not be echoed;
rather, the bulk dump data will be transmitted.
(bulk out).......................................ALL/1–128
Transmit the contents of scene memory from the
MIDI OUT connector as MIDI bulk dump data.
Specify the desired value and press the STORE
switch, and the bulk data dump will begin. While the
data is being transmitted, the MEMORY display will
indicate " ."
• If " " is selected
Bulk dump data for all scene memory numbers (1–
128) will be transmitted.
• If " "–" " is selected
Bulk dump data for the corresponding scene memory
number (1–128) will be transmitted.
(bulk dump request) .....................ALL/1–128
Transmit a message (bulk dump request) from the
MIDI OUT connector to request transmission of
bulk dump data. If another M2500 unit is connected
via its MIDI IN/OUT connectors, the scene memory
contents of the other M2500 will be copied to the first
M2500. Specify the value and press the STORE key to
transmit the bulk dump request.
• If " " is selected
A bulk dump request for all scene memories will be
transmitted.
• If " "–" " is selected
A bulk dump request for the scene memory of the
corresponding number (1–128) will be transmitted.
The Scene Memory function
.............on/oFF
(factory setting: "
(factory setting: "
," messages will be
M2500—Owner's Manual
")
")
35